Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
I am using the TWI module in master mode, with sdk 10. I purposely create an error situation, in which the TWI gets stuck and keeps returning NRF_ERROR_BUSY every time I try...
I've completed the Custom service tutorial, and I wanted to port the system to use the SDK10 with the pack installer. I've run into an issue though.
The code runs fine...
Are the GPIO pins in disconnected state during the startup until they are configured by the Firmware?
If not what is the state of the GPIO pins during startup?
Hello.
I have problems uploading with DFU OTA any application. For this case, I am using "dual_bank_ble_s310" example.
First of all, I put this memory's configuration...
Hi,
I am using nrf51822 CDAB version chip which has 128kb of flash memory, my code is built on ble_hrs
I am trying to save my app_trace logs i.e., redirecting my printf...
Hi,
I'm using pca10040 board. For my requirement i'm using FreeRTOS. While creating task we need to set stack size for each task.
For that i created only one task with...
Hello,
i would like to scan for a custom UUID Ventor. And when the BLE Central found this BLE Client.
I will Change one Output pin from low to high.
I start with the...
hi,
after connecting to peripheral device. app_timer_cnt_get() function always gives 0. why it is so. i am not able to understand it.
can anyone help me to get the current...
Hi all,
Can I do something like this:
The SPI master sets CSN line low.
The SPI master sends multiple packets. And the total number of bytes exceeds the...
I want to transfer data collected in my nrf52DK to nRF51 dongle at regular intervals. Right now I can use master control panel in PC to receive the data. Is there any way...
I am using the bootloader from github here to upload DFU over-the-air using an android phone. It works fine for bootloader and application uploads. But if I upload the softdevice...
I'm looking for a radio module for a harsh environment (steelworks furnace)
The module has to work at high temperature 80°C and must transmit 16bytes every second at a distance...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi. I'm using PCA10028, SDK10.0.0, S130.
Recently I'm testing SYSTEMOFF mode.
Unfortunatly My board is not operate now.
KEIL can't connect PCA10028 baord any more.
Here...
i use a ppi channel 0 to connect timer2 and adc,when timer2 compare event happen,the adc task start begin.then,in the adc interrupt handler,i read the adc result into the...
