Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi All,
My issue is may connected to
I'm using:
nRF52 DK dev. board
nrf52dk_nrf52832_defconfig
I get communication errors very several times. (More than...
Hello, I am a beginner to this Bluetooth Direction Finding Topic. I worked with nrf boards, making them work as transmitter and receiver and got the IQ samples in real time...
When I load the firmware, the firmware starts running fine.
but once I power off then on tue device the firmware crashes at a certain point while in the main loop with no...
Hi All,
As part of the software development, we are required to use an automatic tool for Code Coverage.
We use an nRF52840 device, C language and 15.3.0 nRF SDK on...
Has anyone succeeded in BLE bonding with a Philips Hue lamp or a Hue smart plug with a nRF52? Directly with BLE, without a gateway. I suppose I have all the rest figured out...
Mcuboot manages firmware versions and is able to avoid fw downgrade.
Is it possible to define a product id to avoid to exchange fw for different product of same manufacturer...
Hi,
I want to prepare the scrip for Wi-Fi radio test commands. I am testing the RF performance on nRF7002dk and in order to test the each channel i have to run the below...
Hi,
We have run into an issue when debugging code with the nRFconnect sdk debugger. A breakpoint set in an interrupt service routine is not hit, however, we can see through...
Hi,
I have a piezo microphone with analog output and would like to record from it using the Line In AUX on nRF5340 Audio DK.
Currently, I am using the break out pins...
Current goal is to be able to program, and upgrade with the radio off, and the only connection as a UART.
But I'm both overwhelmed by the number of options (DFU, SMP, and...
Hardware: nRF5340DK
Software : nRF Connect SDK v2.6.1 (any reasonably up to date is fine)
Hi,
I'm new to Zephyr and Nordic and I want to make an example multi-core application...
We have a custom board based on the nRF52805 that does not have a HFXO or LFXO. We are using NCS 2.6.1.
When the firmware thread is idle, current consumption as measured...
Hi,
TLDR: Tried the new BLINFO feature on an existing app, upgrading to 2.6.1 SDK (Zephyr 3.5.99). App does not boot after merged.hex flashed.
So we are updating our project...
Hi,
I am trying to figure out how to change the automatic gain settings on the on-board microphone. It is connected via its I2C to the hardware codec, but apparently not...
Hi i would like to connect an led with mcu (NRF52832-QFAA-R7) and control the led with PWM. while investigating in datasheet i found "Three PWM modules can provide up to 12...
