Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hello, I'm developing on an application which requires to catch high speed, variable size and bursty (~0.5 Mbit/s) data from a sensor connected to a nRF9161DK trough a UART...
I'd like to use the DeviceTree Visual Editor to create the DTS for a custom board starting with only the bare device. But it seems for some reason that the DeviceTree Visual...
Hello,
I’m using the Thingy91X board (nRF5340). For my application, I need to run BLE and Wi-Fi simultaneously, so I have to increase the application size. To do this, I...
Hi I'm trying to work on OTA implementation for zigbee with nrf52840-DK boards.
there is a sample available in ncs2.9.0,light switch,but i understand it can only work as...
Hello,
I have some issues to do function an ntc thermistor with a nrf54L15DK.
An error about a wrong configuration of the adc reference or or the ADC gain appears almost...
Hi,
I have some problem when scan advertising packet using nrf52840dk with ncs v2.5.0.
when I scan during 30s in the same position, I got a list rssi value same that...
Hi Team,
Hello Team,
I'm currently working on integrating the Sensirion STS40-CD1B-R3 temperature sensor into the peripheral_ht . To do this, I pulled the STS40 driver...
When I used the CS instance for distance measurement, I wanted to set multiple initiators. Therefore, I configured BT_CTLR_SDC_CS_COUNT to 3. However, I didn't know where...
Hi there!
We are currently evaluating a low-power BLE system for a safety-critical wearable application that must transmit immediate alerts to a nearby receiver or mobile...
I followed the instructions at https://nordicsemiconductor.github.io/pc-nrfconnect-docs/create_new_app to create a new pc-nrfconnect-boilerplate app locally.
However, npm...
We have a common codebase with both softdevice (nRF51/52 code) and now zephyr (nRF54 code). To make our code compatible I have the following replacement to sd_temp_get. This...
Hello Nordic team,
We're experiencing a GNSS issue with our nRF9160-DK (PCA10090 1.1.3 2024.44) and would appreciate any guidance you can provide. About 4 days ago, we were...
Hi Nordic Support Team,
I'm currently experimenting with Channel Sounding using a couple of nRF54L15 boards.
I am trying to obtain raw I and Q samples so that I may analyze...
ncs v2.6.1
If I use bt_conn_le_create() and do not use the default (0) value for create_param->timeout, the actual connection creation timeout does not match the description...
