After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
nRF52840 does not mention medical as one of the application areas. Is there any specific reason for this? Any hardware or software requirements not met in order to use it...
Hi, I tested Central HIDS example in nRF Connect SDK 2.1.0 with NRF52840DK. The example works with my BLE keyboard, but does not work with my BLE mice. The followings are...
I am unable to use UART 1 with a very simple use case.
All I need to do is enable an interrupt callback when there is data to receive from the UART. I know that UART0 is...
Hi
I am facing range issue in transmitting and receiving data over ZigBee in nrf53833, how can i improve the range maximum i am able to recieve signal from around 35 feet...
Hi All!
I am using Zephyr RTOS NCS v2.0.2.I used uart_central and uart_peripheral apps. But it Can only connect one peripheral with central at a time. Is it possible to...
Dear Nordic,
I am currently working on a USB project were I am interested in building a USB audio device with two-way volume control, i.e. such that both host and the device...
Hi
I am trying to connect my own mosquito MQTT broker. I created certificates and I uploaded all certs through the LTE Link Monitor. I defined
CONFIG_AWS_IOT_BROKER_HOST_NAME...
Hi,
I have been working on a setup where I connect a sensor (TI ADS1299) to the nRF5340-DK 2.0.0 using an SPI connection and transmit the recorded data using BLE. I have...
Hi team,
I am using NRF52833 DK with PCA10100 on it and s140 soft device version..
While writing data into the flash, it is not updating.
Here I am attaching my fds...
My device and Software details are as below
nRF52840 DK
nRF connect SDK 2.0.2
Want to verify USB device role for nRF52840 DK.
Found the below example and its documentation...
Dear Nordic Support,
Please help me with following.
Hardware - Thingy:91 1.0.0 (2019.43) PCA20035
OS - Windows 10 64 Bit
Laptop - HP core i5, 8GBRAM
I want...
We are using nRF Connect SDK 1.8.0 with Seggar Embedded and I have a number of questions.
1. What is the best Nordic example for ADC on this platform?
2. While we have...
Hello, I have defined the vendor_model and the corresponding opcode on the mesh, but the client and server cannot correctly transmit the information, so I can input the corresponding...
lHi,
MeshSDK v5
Hardware: Devboard and custom 2*2 panel light
Running a light server with lightness and ctl control.
I wanted to know how to adjust the light transition...
Hi, I'm using NCS v2 building on VSCode and failing to mount a RAM-backed fatfs instance.
I looked at the code for the usb mass storage example ( link ) for the code.
...
