Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hello,
I am working with nRF5 SDK v17.1.0 and using nRF52832DK board. I want to use the hardware timer in continuous mode and also want to use all 6 compare channels of...
Hi,
I am looking for nRF Connect SDK v1.5.2 and it does not appear to be one of the options in Toolchain Manager v1.1.3. Could you let me know how I can get SDK v1.5.2?...
After
west init -m github.com/.../sdk-nrf --mr v2.0.2
west update I notice ncs/v2.0.2/zephyr has huge difference with github.com/.../sdk-zephyr main
Like there is no...
I've got a PPK2 kit which I am using for quite some time now.
Today I upgraded nRF Connect Desktop and the Power Profiler App which gave me the following versions:
nRF...
nRF Connect SDK v1.8.0, Zephyr, Zigbee, ZBOSS I have an issue with Alexa Echo Gen 4 Zigbee Discovery and a malformed packet when modifying the nrf/samples/zigbee/light_bulb...
Hello Group,
I’m using nRF Connect SDK v2.0.2 with Visual Studio Code (up-to-date). When I open “Open VS Code” from Toolchain Manager v1.1.3, it shows a warning of conflict...
I'm using 52840 device with SDK V14.2.0. and SEGGER IDE.
app_util.h flags _Static_assert as an error.
sdk/modules/nrfx/mdk/compiler_abstraction.h:118: #define _Static_assert...
Hi,
At our factory, the employees would like to have the AT command set exposed of our nRF9160 devices.
Since we would like to use PPP-sessions with our modem, we would...
Hello,
I would be grateful if someone can help me to understand what I’m doing wrong or missing with my setup:
Basically, I’m using the UDP application with Thingy:91...
Using SDK 15.3 on the embedded side and Android 10 I think it is on the mobile side.
We've implemented whitelists and hanging onto the bonding information on the embedded...
Hello,
This is more of a general question about how to best assure that bluetooth is working. The problem in my setup is that i wont be able to access the chip physically...
Hi
I have gone through the ncs documentation and have couple of questions reg the difference in network core and application core and reg the developing solution using nRF5340...
Hello,
We have used the nRF905 in our products over many years. This time we have decided to design the circuit on a 0.8mm FR-4. The recommended layout and BOM suggest to...
Hello,
I've used the Nrf-Sniffer a zillion times before and I really appreciate the existence of this tool. Thanks a lot! Now, I want to run the tool on my new M1 MacBook...
Dear all
I am trying to figure out the range for the connection parameters, I understand that the connection intervals are range from 7.5ms-4s from the post here . But it...
