After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
The Edge Impulse firmware compiles and flashes to the Thingy53, without problem. I would like to increase the range of the BMI270 accelerometer, but can't find any reference...
I am using 52840 and SDK V14.2.0. When compiling nrf_ble_dfu.c I see the following error in nrf_dfu_types.h: line 258
"two or more data types in declaration specifiers....
Hello,
I am getting 0x07 error code when invoking sd_ble_gattc_char_values_read(..) function.
I am using SoftDevice 140 v6.1.1 APIs. I have an NRF52 dongle and I programmed...
Hello,
I am trying to send status messages to a Client model with a specific unicast address on one node. This node's parent element has both generic onoff server and client...
When i define macro
CONFIG_LOG =y
i want to use log
The program can not build successfully
FAILED: zephyr/zephyr_pre0.elf zephyr/zephyr_pre0.map cmd.exe /C "cd...
Hi,
I am trying to send the data received over BLE from nrf5340 to ESP32 and then from ESP32 to nrf5340 using UART communication using below configuration.
nRF5340 esp32...
Hi
I'm wrkig with nRF5 Software Development Kit v17.0.2 and BLE Mesh. When the device is running, after some hours of operation, the NRF_FAULT_ID_APP_MEMACC is getting triggered...
Hi,
I am using nRF connect SDK V2.0.2 chipset 52832 built using VS code.
Need to move the setup from an external clock to an internal RC oscillator.
When I disable ...
The following Pin definitions for QSPI result in Errors during build using NRF Connect SDK. This exact configuration is working on a custom design using nRF5 SDK using the...
I want my client to advertise forever so I added the following code:
static void ble_evt_dispatch(ble_evt_t * p_ble_evt)
{
ble_conn_params_on_ble_evt(p_ble_evt);
ble_nus_on_ble_evt...
Hi,
My device was designed with SDK 15.0, the APP_ADV_DURATION is set to 0 in order to have the device in advertising for all time.
Now I try to use the SDK 15.3 but when...
I've got an embedded application where I want to stream from my device to wireless headphones. Really looking for legacy (I think) right now as I'm not sure LE audio is supported...
I'm getting an occasional MPU fault on the nRF52840 on the Thingy91 when starting scanning:
Running arm-none-eabi-addr2line leads me to
buf->len -= len;
in...
Hi,
I am working on PWM and i am using bellow function for pin set cycles and it's working fine as per Duty cycle and frequency
i am getting the wave form also but i'm...
