Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hello,
I'm working on getting PSM mode with the Serial LTE Modem on the nRF9160 v1.0.0. The power consumption of the modem (26.4 uA) is too high compared to the documentation...
Hi.
I am using nCS with vscode to develop an application, So far I was only working with peripherals and my build file (.bin) size was about 70kb. Now I want to add BLE...
Hi,
I have a strange question about app_buttons, I have two buttons, only one of the buttons is initialized, which works well, but once both buttons are initialized at the...
Hello,
I am currently trying to include one of nordics flash examples into my project. Ive tried both, flash_fds and storage example. Unfortunately both will assert after...
Hello,
Is it possible to get an example for pc-ble-driver iBeacon detect/scan example.
I see only that one with heart rate, not sure what to modify for iBeacon scan/filtering...
hello everyone ,
i have posted a problem regarding Adding BSEC(bosch sensor ) library using vs code for thingy91 13 day before and i am still begging for help .If Edvin...
I am finding myself seriously lacking in proper explanations of how aspects of the SDK work. For example i am currently trying to gain a full & in-depth understanding of the...
i am compiling sample code for accelerometer from sample C:\Users\mohit\nrf\v1.9.1\zephyr\samples\sensor\adxl362 .
i don't make any changes in code . when i try to build...
Hi,
I am debugging an Application running on a custom board that uses the NORDIC nrf52832 processor connected to an IMU over twi. I am using SDK17.0.2
I find WDT is kicking...
Hello Nordic Team,
I've been having good success with the 52840 and been slowly migrating a lot of my projects to the chip. While I await modules to arrive from a supplier...
I'm trying to use 9-bit UART communications with the nrf52840 using nRF Connect SDK v1.9.1, but I'm getting an error -134 when I call uart_configure().
When I use UART_CFG_DATA_BITS_8...
Hello,
NCS1.9.1, nRF52840DK, Windows10 X64, VS Code,
1.
i want to read voltage from RT_ADC pin (P0.04),
and than converting NTC thermistor value to Temperature.
...
Hi, I'm doing experiments with Bluetooth direction finding. I am using the example of the nRF52833 development board, and I have obtained the IQ representation of CTE and...
Hi I am using the aws_iot example on the nrf9160 DK.
I have opened the zephyr.dts file and in the section uart0: it has the following
I've reached this point trying...
