Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi,
1. How do I resolve this error?
2. waring line 93->line 165
3. error : line 104,line114, line128,line 138,
Thank you for all your assistance. Kind regards, Peter...
Hi,
ncs v1.9.1
dk: PCA10090 0.9.0
example :serial_lte_modem
Does this example have the following capabilities?
1. The hex data received from the server in EDRX...
Using the UART example of the 52DK with the TX and RX pins set as 8 and 6 the example works. If I try to change the pins to different pins such as 22 and 23, it does not work...
Hi,nordic
I'm looking for L2CAP Connection Oriented Channels example in NCS,such as Object Transfer Service.
can you tell me some information？
Thanks.
TRANSLATE...
Hi everyone, i would like to put this topic here so that new developers can benefit from it i hope.
when you want to measure the current you need a PPK-2 or Oscilloscope...
Hi expert,
I use the example below:
D:\Nordic\nRF51 SDK\nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_uart
I changed UART pin from default pin0.08 and pin...
My goal is to implement dynamic pairing and connection to a Bluetooth device based on SDK16.0.0 and s132_7.0.1, and add a buttonless DFU function. By sending instructions...
I am trying to integrate GitHub - NordicSemiconductor/IOS-DFU-Library: OTA DFU Library for Mac and iOS, compatible with nRF5x SoCs library in one of the SwiftUI mobile application...
I was starting from multi-NUs.I need to send form a Master a message to 4 Slave every 50mS.
I see that up to 100ms It work but that at 50mS the comunication doesen't work...
Hello,
I was given a project that was built using nRF Connect SDK 1.6.0. I tried installing nRF Connect SDK 1.9.1 but received a bunch of compiler errors when building the...
We upgrade our project from nrf-sdk 1.7.1 to 1.9.1 and it broke part of our project.
The part that broke counts the number of falling / rising edges and triggers different...
Hi team,
I am currently working on a BLE project using nRF5 SDK 17.1.0, I want to interface the nrf52840 DK with the Nrf21540 EK to expand the range.
After reading various...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
I tryed to reduce the power consumption of my beacon (ble_app_beacone example from SDK) to have more battery live. To do this, I want to reduce the TX power. And also change...
I have to initialize a i2c multiplexer, for that I am sending the device address and register address to be written using the function:
nrf_drv_twi_tx(&m_twi, (0x70), tx_buf...
