We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
I am trying to bring in the spi_nor driver into our project and was getting errors reading back the jedec id on initialisation so I tried to run the nrf/samples/nrf9160/http_update...
Hello, I have a problem when I enable Bluetooth on my application. If I enable Bluetooth, I can't control gpio pin on Trace DATA. If I disable Bluetooth, I can. It's a hardware...
Hi,
nRFConnect SDK Sample not working (periodic_adv _sync)
I have two nRF52840 DK with nRFConnect SDK 1.7.1
Compiled and run on nRF52840 boards:
\ncs1.7.1 \zephyr...
Hi There
Is it possible to connect to nRF Cloud using a normal 4G/LTE Sim? I see the specs of the NRF9160 show that it supports full LTE and all the Bx bands.
If the answer...
hi,
I am beginner and I am converting an Arduino library to Nordic library, but I have this part code
what is mean begin, I am confused on this part , for example , TwoWire...
Hi,
I have been programming and testing ESB on the nRF52 DK using the Arduino IDE with the sandeepmistry code base, as it allows me to view serial output to a log screen...
Hi, I'm trying to enroll my nrf9160DK preview kit in nrfcloud. I've successfully done it with my Thingy91, but in process of upgrading modem on Thingy91 with my DK I forgot...
hardware board : 52840dk_52840
sdk : ncs1.7.1
IDE: Visual Studio Code
in our OTA design , we have new image download and stored in a LTE module, since our application...
Hello,
I use ST's mcu + Atmel radio IC + nRF21540 as the FEM. Use Atmel radio IC's IO to control the TX_EN and RX_EN pins for nRF21540 automatically.
I want to change...
We plan to create a BLE central device to communicate with our peripheral devices. Both sides are based on the nRF52840 using SD140. As we've already developed the peripheral...
Hi,
I just turned off compiler optimizations with CONFIG_NO_OPTIMIZATIONS=y (before that, code was working correctly). After the change, I noticed that my program is stack...
Use Microsoft Visual Studio Installer Projects to create .msi for nRF-Command-Line-Tools-10.14.0-x64.exe and other .exe files, but an error message will appear during execution...
Hi,
Is it possible to create two separate USB devices on nRF5340? My application requires three USB classes: Audio, CDC and DFU. Currently I am using all three in a composite...
