Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi Nordic
I have some questions regarding switch to Application on custom address.
The memory layout in flash is like this:
0x00000000 - MBR 0x00000000 - softdevice...
Hi, I am new to the nRF Connect extension in VS Code and I am having trouble including dealy.h header file to utilize a DelayMs() function. I found the delay.h in the sdk...
I am advertising some data, my hardware is minimum and there are no external interrupts.
1. How do I wake up after entering power save mode with __WFE(); ?
2. I also want...
Hi ,
I want to use above PMIC for Gotek tracker. But I have below questions:
1. Due to the IO limitation, can I use static high or low to configure the chip with VOUTB...
Hello,
We are working on a product that has UART and SPI integrated. We initialise the UART and the SPI at the beginning of the code and everything works fine.
However...
I am using the nRF52840 and the pair of Nordic BLE UART Demo projects ble_app_uart_c_pca10056_s140 and ble_app_uart_pca10056_s140
Please can you tell me how to change the...
Hello all, Currently I am developing a code for a BLE central device that is supposed to receive data from a weight scale (peer). The peer has a service with a custom 128...
Dear friends,
My 52840 DK flashed a serial example(nrf5_SDK_for_Mesh_v5.0.0_src\examples\serial) as a provisioner.
Now, I want to factory reset my provisoner by PyACI...
Good day,
We are trying to interface TCAN4550 to nRF52840 over SPI, and found that sometimes TCAN throws SPI error (underflow of read/write). Looking further, we found that...
Hello all,
I am developing a BLE application with the Softdevices, the peer management module, and with MITM protection.
I've set a bonding static passkey as shown here...
I run a custom multilink BLE service server on nRF9160 DK.
After about 20 minutes of repeated connecting, data exchange and disconnecting from 4 (only four) BLE devices...
Hi,
I need your help to know "How to control RGB LED using PWM in nrf5340?". I have already tried the "RGB_led" sample in NRFconnect SDK v1.5.0
But can't able to control...
Hi
I have nRF52840 DK with nRF5_SDK_17.0.2_d674dde
I am using radio_test example code under examples\peripheral\radio_test:
Radio Channel is fixed at 10,
The data...
Hello,
I am searching for the PCB layout showing ground connections on the nRF9160 Development kit. I was unable to find the DK layout on the product website. Also, I...
Good day, dear developers,
I am using nRF52840 with SDK15, no OS. System has 4 SPI devices (2xSPI, 1xQSPI, 1xLCD controller SPI) and 1 - I2C, all having dedicated bus (no...
