Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hello.
I need to add an output gpio to the dts file, I modified the board.dts file, inserting these lines in the leds section
res: res_ {
gpios = <& gpio0 17 GPIO_ACTIVE_LOW...
To flash a new firmware I always do the same thing.
Open NRF Connect
Open Bluetooth Low Energy
Click: Start Scanning
Click: Sort by signal strength
Choose the...
Hi,
As well know, nRF52832 have more then one SPI and TWI interface.
How can I use SPI and TWI interface in the same program? for example, use SPI-0 and TWI-1.
Thank...
I don't understand how the guide gets to the Open IDE button. I used the automated installer and it did not appear for me. The guide did not provide any instructions on how...
I see that in the 6.20.14.20 RXADDRESSES in Reference Manual I can enable multiple addresses in the same time, so is it possible for nrf52840 to listen on several addresses...
SENT protocol uses a 1-wire interface to transfer data using time intervals. To receive data you simply measure the time between pulses on the wire. The transmitter never...
When I use the BLE mouse example in the nRF5 SDK (17.0.2), it works on iOS (14). However, the report is divided into 3 parts. I would like to combine the mouse buttons, X...
We are developing a controller for an Electric vehicle charging station. Already developed and successfully running the firmware on ESP32 for which we had used platformio...
I am using this tutorial to write a custom service and I got to a point to add custom characteristics and got a few questions:
- I don't seem to find any characteristic...
nRF52832 nRF5 SDK V17.0.2 SoftDevice S132 V7.2.0
I am running the sample program ble_app_uart in the above environment, but sometimes I miss UART received data. Teraterm...
Hi,
I want to do a custom developpement (custom board) for my project.
I have copied to a folder on drive D/: the peripherial_uart sample, as well as the folder Board...
Hi
We are trying to configure Nordic UE (NRF9160) at our local setup. In order to flash software we performed following steps:
We used ' carrier_deploy_e7f4d5d4-f607...
Hi,
I am looking to design a nRF52833-CJAA (WCSP/ BGA package) board using 4-layer stack.
a) do you see any issue in doing that, vs. 6-layer stack used in nRF52833-DK...
Hey
We encounter problems with the modem not establishing a connection after rebooting the processor for a few times.
Issue:
Firmware is booting normally
Cellular...
It support send periodic advertising with CTE in ncs v1.6.0, but I found that the scanner can establish synchronization with only a tag that sends periodic advertising. But...
