This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi everybody, thanks for your time.
I try to develop an iot board with FOTA. To do so, I have a custom bootloader (address 0x00000000 in flash ) who perform the following...
Dear Members,
How can I increase ANT+ BSC time out ?
I read from nRF5_SDK_17.0.2_offline_doc/nrf5/ant_examples_bicycle_spd_cad.html
User interface
If a time-out occurs...
Hi,
How to get a same interval between the two events . I am seding the data from nrf52832 to phone every 1second . I want a uniform interval between the two data please...
Hi there,
I've set up an nRF52840 DK with an external power supply of 1.8v and also connected the USB IF MCU to my laptop. I've positioned the VEXT->nRF switch to "on" and...
I am creating a BLE central device. This device has to communicate with BLE advertisers to collect some data from them and then send this data to server. I am currently achieving...
Hi,
My project already has the ability to DFU throw BLE.
How can I add to it the Serial DFU throw USB ?
Is it possible to have one boot-loader that can handle both...
Hi there!
I have run light switch example for Mesh demo but no activity could be found via nRF Mesh app even my dongles have never been provsioned.The version of SDK and...
Hi Team,
In my application I m using NUS and and a custom service.
Everything works fine in redmi note 4(android version 7),Lenova K9(Android version 8) and Samsung Galaxy...
Hi,
I'am trying to program my nRF51822 module using keil IDE. I have taken some example code which is present in the SDK 12.3.0 and soft device-130.
Please let me know...
Hello
When I send data over BLE, I got this messages in debug terminal.
<info> app: Debug logging for UART over RTT started. <info> app: Connected <info> app: Data len...
I have seen other post on this issue but they are not helping. I am using the bmd 330 to run ble_app_uart. It compiles and advertises correctly but does not send the tx and...
Hi,
I am facing issues in Flash Data Storage (FDS).
Here, nrf_fstorage_write function is returns with NRF_SUCCESS but not writing in actual memory location. While nrf_fstorage_is_busy...
Hi. I am now at the stage of creating a new project. I want to include DFU over the air support in it. So, how can I do this using the example of two projects (secure_bootloader_ble_s132_pca10040...
How do you use the nrfx_temp driver in a project? I'm on SDK 17.0.2, segger, and an NRF52840-DK board. I see the old HAL temp sensor is deprecated and it seems to always return...
Hi,
I have been using a certain 16MHz oscillator up until now without any issues, and now wish to replace it for logistical reasons, what kind of testing are recommended...
