Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi, I’m working with an nRF52840 DK and trying to use two UARTs simultaneously. I’ve configured UART1 for debugging (console and shell output) and want to use the default...
Hello, I am trying to use the subghz template in ncs 2.5.2 but I am running into an issue when enabling NanoPB. When enabling NanoPB with CONFIG_NANOPB=y the application faults...
I have noticed that Matter V1.4.1 has been supported from NCS V 3.0.0( https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/protocols/matter/index.html ), but I have not...
Hi everyone,
I'm developing a Matter device on the nRF54L15 platform using NCS 2.9.0. When commissioning the device via HomePod and iPhone, the device unexpectedly reboots...
Hello, Super quick but important question, are the SMD footprints in the nRF52840 reference circuitry recommended BOM (ie image attached) in imperial or metric units? and...
After full update modem firmware and reboot, i got this error:
E: Modem library init error: -116, lte_lc not initialized
The only way to work around is power cycle.Po...
Title
nRF5340 DK × 2 + MCP2515/TJA1050 – can_start() = -5 (CANCTRL/CANSTAT = 0xFF). What am I missing?
Hi everyone,
I’m trying to bring-up a very small CAN bus test...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hello!
I have tried in various ways to make the XIP part functional on SDK version 3.0 (SDK v3.0.0-3bfc46578e42) but without success, this on the NRF5340 devkit. I mention...
Hello nordic team!
Context:
Currently I am working on modifying our application code to be able to select, at runtime, which network interface it will use (between ethernet...
Hi,
am working on nrf52840 withst7789v custom display . I have integrated the my display code using lvgl library with PMIC code in zephyr . while doing that I have configure...
Hi. I had a working MCUboot configuration that I used in order to update both the app core and the net core as follows:
- Upload the app core image using mcumgr - Upload...
Hi. I used nRF Connect SDK v2.9.1 to add OTA to the Peripheral UART sample application. The target is nRF54L10, but when I build it, the flash usage exceeds 50%.
If the...
Does nRF9160 support IoT devices, SGP.31 eSIM IoT Architecture and Requirements for remote provisioning of eUICCs in Network Constrained and/or User Interface (UI) Constrained...
Hello, we've a nRF9161 DK board a we saw on the back side a footprint for mounting an SD card holder and we found the SD card holder component in the BOM.
Unfortunately...
