After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hi,
Is there any sample Android mobile application available which calls or consume the Temperature/humidity for nrf5_SDK_for_Mesh_v3.2.0 ?
Best Regards,
Hi,.
I am using nRF52832 , sdk 16V
How many samples can be sent over ble if we set 7.5ms minimum
I need to send the 100 samples. I tested by setting to it 7.5ms I think...
H i everyone, I'm having a problem as follows: I am wanting to use LPCOMP to wake up the nrf52840 from system off mode. So can anyone give me an idea of how to do that?
I tried Searching for the NRF_CCM structure, but could not find it.
Where should it be nor the MAXPACKETSIZE.
this code is in the system_nrf52840.h
Also, could you please...
Hi
We are doing field trials of a nRF52840 product with s140 SD, now and again NFC stops working (tag type-4, read and write).
This has been seen in SDK15.3.0 with SD6...
Hello,
I would appreciate some guidance about BLE connection stability. Our product is a system of 3 peripherals (custom board with Laird's BL652 module, containing nRF52832...
Hi,
I have a project which requires using trace data pin P0.18 as an SDA for the sensor, but cannot send
anything because it doesn't generate anything and the program...
Hi, we are moving from nRF52840 DK to integrate nRF52840 to our solution. In the datasheet for pin assignments ( Link ) it states "recommendation usage; Standard drive, low...
I'm currently running nrfjprog version on OSX. Version info below:
When running a nrfjprog -e I expect that the device doesn't do anything afterwards. When monitoring...
I'd like to use two nRF9160s to do D2D (Device to Device). Is it possible? For example, if you press Button 1 on nRF9160 (1), then LED 1 on nRF9160 (2) is displayed. Is it...
Hi,
our company is developing some different models of devices with BLE based on the nRF52840 MCU, working with the nRF5 SDK (17.0.2). The devices are in parallel using...
Hi All,
I am working on the nRF52840 Zigbee protocol and I am using nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71 SDK.
With the help of engineers and other stuff, I am...
I updated the nRF Connect SDK to latest master. It currently uses Zephyr 7d20f2ebf2. Most of the time (~4 times out of 5), calling sys_rand32_get() crashes the firmware and...
Does the ZBOSS stack have an API that provides network statistic or network health details? We would like to get a general understanding of state of the network.
Thanks...
Hi
I'm using SDK_17.0.2 with softdevice S132_7.2.0, can anyone advise DFU SD version code for this?
I can't find it in list below, the last version is S132_7.0.1, thanks...
