Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hi,
I am trying to write a file in flash(nrf52840) at a particular address & after that i want to instruct DFU module to start FW update from that address?
Is there any...
What are the situations where a SoftDevice calls reset handler?
I have a somewhat heavy data collection (lots of event handling) and those things are logged via RTT backend...
Hello,
I developed an application on a BMD-300-EVAL. This is a evaluation platform with a BMD-300 module (nrf52832 chip + antenna + crystal +...) on it. The application...
Hello,
I have followed all the Getting Started documents to setup the development for my new nRF9160 DK.
Among them, I installed SAGGER Embedded Studio version 4.52
...
I have as starting point the HRS FreeRTOS app. Now I want to add a millisecond counter. But from what I read I'm a little bit confused. Can someone tell me what's the best...
Hello, I am working on a custom NRF9160 and I am on SDK 1.3.0. I am working on the asset_tracker project and I want to put my own accelerometer there. To do this, I changed...
Hello,
I have been using Nordic mqttsn examples (publisher/subscriber) along with an OperThread Border Router. So far I haven't changed the parameters of the Thread Network...
Hi,
I am trying to adapt the read register function that use the TwoWire lib of Arduino in order to read a Sensor Hub Response Byte of a defined Host Command :
to...
Hi
The flash data retention time for nRF52832 have been specified for 10 years @ 40°C. Is there any data available what the retention time would be at higher temperatures...
We are developing tracking system for our ground floor car parking but couldn't able to get GPS location.. we install Nordic Thingy:91 inside the steel body. Please let us...
Hello guys,
We are developing nRF52840-based device that needs to act as both BLE Central and Peripheral.
Peripheral role:
In BLE Peripheral mode, nRF52840 should advertise...
I have a need to send pressure data form 1 device to 4 other devices , it is medical application , data rate is in such a way to be in human readable form, can i use nrf24l01...
Hello, Just purchased a nordic NRF5340 PDK from digikey. On plugging the micro USB 2.0 and switching on the device , the device powers up for couple of seconds (LED1 & LED5...
I'm trying to add BLE_UART functionality to a custom board, on top of the already existing USB (and working) USB_CDC CLI. I'm using SDK 15.3.0 and softdevice S340
I used...
Hey
I would like know how can i add battery model for mesh. I have seen the Battery indicator in normal BLE sdk, now I want to implement in mesh sdk in the form of model...
