After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
So I'm not sure that this is an error, but it is a little annoying. I have an application that sends sensor data using ble_nus. Works great, except that mixed in with my data...
To the kind attention of Nordic support team,
In case of a device and host ble bonded, I'm giving a look at disconnection reasons codes due to (1) host entering sleeping...
I have build a project, and it has been running normally. Now, I want to test a font data, so I created a function. But strangely, although the compilation has been successful...
We are developing iPhone application that configures mesh boards. If we try to send several messages in a row (specific case: trying to distribute application key and then...
Hi,
I have NRF_LOG configured with a RTT backend. This works great while debugging, but during beta-testing in the field there is no way to access the log.
Is it possible...
Hi,
I am a bit confused about the effect the Connection Interval has on BLE throughput.
SoftDevice documentation :
https://infocenter.nordicsemi.com/index.jsp?topic...
Hi,
I've implemented a program on the nRF5 SDK, based on the ble_app_att_mtu_throughput example, that sends out advertisements in between periods in which it scans for...
Hi,
We are using nRF52833 chip for our development. We need to combine Application, Softdevice, Bootloader and setting file for production purpose.
In project merging...
The nRF desktop tools are great but all have an irritating bug. I typically hibernate my PC at the end of the day to take it home. When I restart the next day, the windows...
Hi,
I'm trying to link a static library that provided by others to my own project. I followed the steps in this post ( https://devzone.nordicsemi.com/f/nordic-q-a/39338...
Hi all
I'm using nrf52805 soc, softdevice s112 , sdk version 17.0.2 and nrf connect mobile app for my project development. I can connect and disconnect the nrf52 device...
Hi,
I am using P0.10 GPIO of nRF52840 (QFN package) as an output for driving a transmission circuit with an 8MHz digital signal.
According to the datasheet this pin is...
Hi team, I'm using Mesh in my project. Using this thread as a reference, I tried to decrease the data throughput and experiment to see if devices could communicate with each...
hello,
i want to know if is possible have Multilink, ble Uart and relay together? it is for make an a type of Mesh network of 4 devices with a BW of 1Mbps (see the image...
Hi
I'm testing the SLM application in nRF Connect SDK ver 1.3.1 on nRF9160 PDK ver 0.8.2 using the LTE Link Monitor v3.5.0
Giving the following commands, the UART stop...
