After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hello Nordic Pro's,
We are developing a product based on the BLE UART peripheral. We communicate heavily via NUS. There are extended processes that continually send status...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
1) As per below link, do I need to skip GPIO...
I would simply like to see the debug outputs (NRFX_LOG_DEBUG) the NRFX_TWIM.C module using RTT debugger through Segger J-LINK.
I cannot find any documentation on how to...
Hi,
I am working in nRF52832 SDK15.3 in SES
I need to work on reading multiple Analog inputs. in a different timings.
i have seen SAADC example.
is there any multiple...
Hello,
I am working with nRF52832 , a soft based on the NUS service and SDK 15.2 ( S132) .
In the aim of reducing the current comsumption , I want to modify the throughput...
Hi Martin, I follow all the steps in your tutorial(Bluetooth low energy Characteristics, a beginner's tutorial) and I am able to create the characteristics and the notification...
How do I share variable data from my nRF52 application to the bootloader code?
Check the update to this question after first comment by @HungBui
There is some short...
Hi,
I am using three nRF DK (nRF52832 - PCA10040) to test and analyse the mesh network (nRF5 SDK for Mesh v3.1.0).
I worked on light_switch_example with 2 clients and...
Hi.
I'm using the nRF52810-QCAA (DCDC) Reference Design, but I've noticed that C6 and C13 are labeled as No Connected in both the schematic and BOM, but in the PCB model...
Hi,
I am trying to write data to the nRF52 module from my custom application. I am sending few parameters bundled into a packet to the module. One of the parameters is the...
Hi
Im currently having some problems with programming a solution for a small system that im making.
The idea is a mailbox with a dongle and accelerometer that senses movement...
Note that for SDK v12.3 : if application size * 2 > available space a single bank update is performed.
While I am using v15.3 and there seems no more infor about the single...
I installed espruino_1v99_thingy52_app and espruino_1v99_thingy52_softdevice , but i want to restore the thingy to the default firmware. Have a way to reverse to the default...
Is there some instructions to debug the nRF91 sample applications with segger with thread awareness? I've seen mention of freertos thread awareness and have requested access...
Hello,
I have been working on ble_app_uart_coexist to achieve the integration of uart and mesh on nRF52840, but I learnt that nRF52840 does not support this example.
I...
