I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hello All,
I am working on nRF51822 using IAR IDE and nRF51 SDK 12.3.0.
Right now I am checking power consumption of device in ideal mode but right now it is higher. ...
Hello. I tried to understand MMA8652FC Acceleration sensor with 52832.
I don't know what means 16Hz, 8Hz, etc. under table.
I know just concept of High pass filer. that...
Hi, I want to use wolfssl library on nrf51822 and I'm in stuck.At first, I compiled wolfssl as arm-none-eabi ,then added the static lib to the project in segger studio.
...
Hello everyone!
I'm trying to build a project of gathering the information from several temperature/pressure/humidity sensors and sending it to one display.
Sensors will...
Hi, I've tried to set BLE power to max but an app error is raised when I use the sd_ble_gap_tx_power_set function. Parameters should be wrong but as far as I've read over...
How do I align UART transmission/reception with GPIO pin signaling low/high? I wanted to do this because BLE chip is receiving the Product ID & device name from microcontroller...
Hi there,
I was used IAR to compile my source, and combine with bootloader and soft device, and it was always work fine.
Now I have changed my compiling tool to SES IDE...
Hi there,
I am developing an application using an nRF52832, nRF5_SDK_12.1.0_0d23e2a and Softdevice s132 v3.0.0. The BLE part of the application involves sniffing advertising...
Hi All
On my NRF52 device I want to return my own error code after a mobile application (android) has written some data to my custom characteristic. For that I consider...
I am trying to get 2 of the nRF52840 dongles provisioned on a mesh network (client + server). (versions nRF5_SDK_15.3.0_59ac345 / nrf5SDKforMeshv310src)
I am using examples...
Hello
I'm using the NRF52832 with softdevice 132. My SDK version is 15.3. My platform is WIndows 10.
I am having trouble configuring the TWIS. I've followed the instructions...
Hi,
Here's the setup I currently have: nRF52840 SDK 15.2.0 s140 6.1.0 softdevice Secure Bootloader pca10056_usb
I'm trying to update the mbr_params_page (0xFE000) from...
I am new to the Nordic stack, and I have developed an Arduino outdoor prototype using an nRF52840 communicating with another ESP32 (BLE + WiFi) gateway. The project is used...
I use timer+ppi+pwm model.my init code like this
I use some code to close and open PWM ,like this
question:I use oscilloscopes to check PWM, I find that when I start...
Hi all, I want to work with Coded PHY on Bluetooth 5. I tried to change lines on mesh_adv.c file like below, but i getting this error : app_error_weak.c, 119, Mesh error 7...
