Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello Nordic ,
Do i need to implement the config_ client model so that the node can be named as a client and a provisionner in same time ???
however in the example of...
I am using SDK 15.2 with IAR's EWARM 8.30.1 and the nRF52840 Development Kit. My eventual target is the nRF52-Dongle. If it matters my development OS is Windows 7 64-bit....
I would like to write code to disconnect from any connected device. My system is a ble peripheral with s132 6.0.0.
My code calls:
result=sd_ble_gap_disconnect(BLE_CONN_HANDLE_ALL...
I starting working with examples for the nRF9160. Zyphr seems like a very complicated OS (like Linux with device trees, etc) and difficult to use with a debugger.
Is the...
Hi,
I trying to convert a stm32 function code to nRF52. The goal is to use a spi periperal on my custom board.
In this application we need to have 2 bytes transfert. That...
I can communicate with success from the pc to my custom nrf52832 device (SDK 15.2, S132v6.1) using the pc-ble-driver (sd_api_v3) with Tag 4.0.0 from Github. Great work!
...
Hi,
I designed a nRF52832_xxAA board, use an external power switch, without DFU features its operating normally.
When I add the DFU function according to the Sample code...
Hi,
I am using nRF51822QFAA-R7 controller(DC DC setup) in my design.
I am generating +3.3V from rechargeable battery and providing +3.3V as a supply to drive these controller...
Hi,
I'm just getting started with nRF mesh (sdk V3.00) and I've built the light switch sample successfully and deployed it on three nRF52832 development boards but provision...
hello,nordic
I use NRF52840 QSPI+FatFs+USB-msc(..\nRF5_SDK_15.2.0_9412b96\nRF5_SDK_15.2.0_9412b96\examples\peripheral\usbd_msc),I found there is a bug about write to flash...
I am working on a new design for the nRF52832. I need to match an antenna to the device. My understanding is that the output impedance of the nRF52832 is 53 + J66 for best...
I am unable to toggle LED's on server boards, using Push buttons on client boards. flashed the light_switch client,server, provisioning images on nrf52832 boards using nrf5SDKforMeshv300src...
I programmed my nRF9160DK with the asset_tracker app using SEGGER Embedded Studio for ARM.
What I did was to open the prj.conf file and changed the following from "n" to...
