Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hi! I've got a nRF52 dev kit and I'm programming it with SDK 15 with Keil. When I send 3 consecutive BLE notifications (each notification is 4 bytes) to the Android app, the...
Hi everyone,
right now I have two different kinds of Evaluation Kit: two FRDM-KW41Z from NXP with Thread Demo which can be found with this link:
https://www.nxp.com/products...
Hi all
Being fairly new to the nRF ecosystem I'm trying to get some basic code up and running on a custom board which uses a Rigado BMD-300. I'm using one of the examples...
Running into this with nRF Connect v2.6.1 for Windows
What happens is that the top-level app installs and runs fine, any apps that are added and launched within (or directly...
Hi,
I am working on the ble_app_uart which should forward data to the SPI port of the nRF52832.
It all works fine while the J-Link is connected. If I want to run my application...
I am playing the light switch example with nRF mesh app.
I am using nRF Mesh app read the light server state. and find out the app is really easy to hang when the device...
i am using this project,where can i download the origin app,soft,especially bootloader ?
the flash is been erased, i want the origin hex ,thank you
\nRF52832 pack\nRF5_SDK_14...
Hi,
Am using nrf52832 for my BLE project with SDK 15.02. I found sometimes device is not showing after disconnect, I have to reset the device manually to show the MAC...
I'm trying to update my project to use the latest S110 softdevice release. The trouble is that I have written many of my own hardware abstraction layers and they are conflicting...
Hello,
I am trying to program a nRF51 chip with a dev kit. When I install the base nRFGo Studio, it is able to detect the board but it won't read the chip because it is...
Hi,
I am experiencing an interesting case ( I am not sure if this is a problem indeed).
I have been trying to develop code for ISP1507 (nRF52832 PC10040 based) on two...
Hi ,
I have tried to test the current consumption on NRF52840-DK (PCA10056).
DCDC is enabled.
RTC is running.
No BLE is advertising.
The DK is powered via USB. ...
hi，all
i got the nrf52832 dk and run the ble_app_uart example ,
but i found nothing output in jlink rtt viewer after called the NRF_LOG_INFO("UART Start!") ,
so could...
Hi.
I did the secure bootloader DFU. I attained step 8 in document .
I instal softdevice and secure bootloader to flash nRF52832. After make the ble_app_buttonless_dfu...
Routing the DCC pin on the nRF52832 with the chip scale package is pretty tough. The bump is surrounded on all sides by other bumps, so I don't have room for a via in the...
