We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
I am using a custom nrf51822 board and S130.
I am trying to pull data from a sensor over SPI and then immediately send that data over SPIS to another processor. Is this...
While trying to implement a simple qdec demo application, I find that QDEC_SAMPLEPER_SAMPLEPER_512us above works ok, yet QDEC_SAMPLEPER_SAMPLEPER_256us does not work at all...
I have a case where I'm using a timer/counter as a counter with one PPI channel routing a GPIO rising edge to the COUNT task. Another GPIO rising event controls the counting...
I have an nRF52 paired to a central device. In order to delete the pairing on the nRF52 I clear the persistent data (dm_init_param_t).
I notice, however, that even though...
Hi all,
I'm a grad student trying to innovate on the BLE concept. I require a continuous signal as a source: preferably unmodulated, but a long duty cycle could also work...
The NRF52 product specification (aka, datasheet) has 3 chapters in it all relating to TWI: TWI (chapter 49), TWIM (chapter 33), and TWIS (chapter 34).
Which section (TWI...
Hi,
I'm trying to interface SIM808 with nrf51822 over uart using nrf_drv_uart. Everything works well for some time, but then uart starts reporting error code 1, NRF_UART_ERROR_PARITY_MASK...
Hello,
I am working with the GPIOTE library to get a GPIOTE_IRQ from a peripheral.
I have several questions regarding the library and how IRQ works.
1.How do I clear...
Hello,
I am using SDK7.1.0 for NRF51822.
In my subroutine, I would like to disconnect with the peer device, and re-advertise. But when after re-advertising, I found the...
Is it possible to set scope for search in info-center only for SDK 11? It search in all SDK versions and sorts results randomly. It is very annoying. Especially when there...
Hi,
I want to build expertise in BLE and want to use the Nordic nRF51x22 to build a hardware and write the firmware for the same.
I am planning to use the nRF51 DK....
I'm calling sd_ble_gatts_characteristic_add multiple times to add characteristics to a peripheral. At some point I get a return value of 0x200020B6. I'm not making much headway...
Hello everyone,
I am trying to use the ble_app_hrs_rscs_relay example from SDK V11 for s130 (2.0.1).
It compiles and works well when I use an pc10028 evaluation board...
If I have multiple services, 2 for example, how should I set up the srdata.uuids_complete.p_uuids in the code:
ble_advdata_t srdata;
memset(&srdata, 0, sizeof(srdata)...
Hello,
I am developing beacon on nRF51DK and I want to store in non volatile memory some parameteres like:
ProximityUUID
Minor
Majnor
AdvInterval
Tx_power...
