I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
I am working with the BBC on the Microbit project. bluetooth nRF51822 has an ARM Cortex -M4F CPU which is MUCH more powerful than the ARM Cortex M0 being used as CPU. Is it...
Since it appears that version 1.20 is broken and useless, does anyone know where to get an earlier version for 64-bit machines? A co-worker has 1.17 for 32-bit but it refuses...
Hi, I just got my nrf51 DK, I compiled the BLE_URIBeacon example from mbed and downloaded the hex file, 361.2KB. I pushed the RESET button and connected the USB cable to my...
Hi
I use an avr attiny441 with the nRF24AP2. Communication is over SPI byte flow. After start up, I get the start-up-message from nRF24AP2. That's fine. Afterwards, when...
Hi all,
I tried to implement a software ACK between two NRF24LE1 devices, but failed.
In my tick_interrupt_ISR, I send a frame from device_A to device_B, and I want to...
I would like to start a pwm signal on PIN 15 while BUTTON_1 or BUTTON_2 is pressed. If BUTTON_1 or BUTTON_2 is released, than there should be no signal(low) on PIN 15.
...
I have built an application using S120 v2.1.0. The app runs fines from 0x1d000. When I run an own bootloader (RS485, no need of interrupts or S120, no pstorage functions,...
hy,
i am using s130 as a central device. I can establish a connection and also read the characteristics. I also enabled notifacation for one characteristic. Everything...
Hello,
I have the latest version of nRFGo Studio (1.20.0.2 version) and i try to program the S310 V1.0.0 SoftDevice using the nRF51 DK. I get the following message : Invalid...
Currently I have a device working with DFU being updated from an iOS device. Now however, I would like to update the DFU from another BTLE device. There is no OS in this device...
As I am using four GPIOTE IN events to get interrupt on gpio-pin's rising-edge, please let me know whether it is possible to get low power or not.
If not, please show me...
I get an error sometimes in my project, and the error code is 0xDEADBEAF always. it happens often when i start advertising and connectting to a mobile phone. i get the debug...
From the nrf51 dongle User Guide, if revert back to the J-Link image from mbed image
download the latest SEGGER J-Link software from www.segger.com and open a debug session...
Hello, first of all: I do not expect support from nordic here, but if any kind sole could shed some light on this, I would be very grateful. I’m developing an open source...
