I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi Nordics,
I would like to run the app example “ble_app_hrs_s110_hci_pca10028 (nRF51 PCA10028)” on the 32 MHz crystal. Can anyone help to change the code to 32MHz base...
Hello,
I am currently use the new SDK 8.0 for the NRF51822 (S110 soft device). I noticed that on SDK 7.0 for the ble_gap_sec_params_t struct , there was a variable called...
I want to see register values in interrupt service routines after a timer timeout. However, when I enable debugger in Keil, it only iterates once to the end of main function...
I've been trying to get a simple blinky program to compile for the better part of a day now. The makefiles are outdated and so are the keil projects. Is this SDK no longer...
Hi ,
I have a code like below.
__attribute__((used, long_call, section(".data"))) void function_1()
{
unsigned int a;
unsigned int b[10];
int c;
c= a-(...
I currently have an application with DFU bootloader that runs on s110 5.2.1 on a rev1 nRF51822. If I upgrade to the latest rev3 chip, can I just flash it and everything will...
How can I compile a simple blinky program for the PCA10024 with the IOT SDK, and using the (iot modified) s110 softdevice?
I've been trying to get a simple blinky program...
Hi all,
I am facing a problem with pstorage_init() function. In fact after enabling the softdevice (S130), I am calling the pstorage_init() function. When debugging, the...
But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
Hello,
I am new in this using of this RF module. I have tested it in many ways. But I'm using this module with pi16f72 So, it has " SDO,SDI,SCK" I have crossed the cable...
I'm working on a project where we're having mulitple nRF51822 chips communicate in a multiceiver way. When we bought the nRF51822 chips, the technical sales rep claimed that...
Hello, we have kind of an in-house serial command protocol that we have used over Rs232, sockets, wifi, etc, and we would like to implement it over BLE. I am inheriting a...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi I'm confused by this statement... Can my characteristic size be more than 20 bytes?
Each outgoing data packet can contain up to 20 bytes of user data (set by the specification...
