Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi,
I’m currently developing an application for the nRF52833 that collects sensor data via SPI and sends it out over BLE using notifications. My primary goal is to achieve...
Hi,
I am trying to create a device two temperature measurements.
I have created two endpoints like this:
but when I try and compile, I get this error:
G:/ncs/v2...
Hello! I am trying to monitor mbedtls heap usage in the azure_iot_hub sample (v2.8.0), building for nrf7002dk/nrf5340/cpuapp/ns. I can see in modules/crypto/mbedtls/library...
I am trying to enable userspace for my project. I am getting this error on one of the last steps related to some debug info.
I can compile fine with all the same configs...
"I added an endpoint called Matter Extended Color Light to the matter_bulb example. After compiling and flashing the firmware, HomeKit only recognizes and creates two dimmable...
Hi,
I want to connect LDC2114 to nRF9160. I write the nrf9160dk_nrf9160_ns.overlay and the astri,ldc2114.yaml. I don't know how to set GPIOs in & i2c1 - ldc2114: ldc2114...
Hi all,
I am dealing with a similar problem to this post: https://devzone.nordicsemi.com/f/nordic-q-a/110715/creating-development-env-for-nzrzf5340-error-warning-nrfjprog...
Hello,
I am using the nRF54L15-DK and nRF Connect SDK v2.8.0, and when I try to compile the Zigbee Coordinator sample, I get an error saying that <zboss_api.h> cannot be...
I'm using NCS version 2.6.1 with a NRF9161DK
Recreating the issue:
Follow the instructions in the readme of the sample: Cellular: nRF Cloud multi-service
Build with...
Hi nRF experts.
We are RF module manufacturer, We are developing nRF54L15d module, When we develop production test software, we need to test power off current, Using the...
I'm trying to get a gas gauge and charger IC to work on the i2c bus. Both have different addresses. I'm able to read from the gas gauge address but not the IC. Are there specific...
Hi Nordic:
I use NRF54L15 for my product and hope to use ANT+AND BLE. Does NCS2.8 currently support it?
I couldn't find a example program for ANT+in NCS2.8. How can I...
Hello support team,
I am developing a mobile app to communicate on BLE coded phy (long range) with nrf5340DK. The nrf connect for mobile on android works fine, but not ios...
We have some devices that run the same firmware, but need different default BLE tx power settings.
There is a KConfig value to set the default, but in our case it is different...
