After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hi,
I believe there is a significant inconsistency between the documentation and implementation of AoA antenna switching in the nRF Connect SDK. My testing of this was done...
I have a custom nRF9160 application running based on asset_tracker_v2. It is working perfectly but I am seeing location error messages. The nRF9160 we have does not have GPS...
Hi everyone! I have a custom board with the Adarfuit UF2 Bootloader ( https://github.com/adafruit/Adafruit_nRF52_Bootloader) and a SoftDevice. With the old SDK v2.5.1 I created...
Hi! So I am trying to control two micro servos, MS18 with the nRF connect app. So far I have the code where I can control it with one instance, and hitting the true false...
I am trying to work with a BLE Mesh network. I am using the nRF5340 as a light and another board, the BGM220, as a switch. Both are provisioned and configured, but the switch...
Hi everyone,
I'm currently trying to build a program with the extension "nRF Connect", and here is how i proceed :
- add build configuration --> nrf5340_audio_dk/nrf5340...
Hey there! I'm looking for the official license info for nRF Command Line Tools and nRF Connect for Desktop. We want to install these on our work computers, but need to check...
Hello,
this is the first time I work with this device and the device is not for me or for my company.
I have to do an automatic test application, which should program...
Hi there,
So I am using an adapted version of the echo sample for I2S in the nRF Connect SDK in VS Code. I only want to use the echo example in receiving mode, so I have...
Hi, I'm using the nrf9160 with ncs2.7 on a custom board. Does the APN need to be explicilty set with `CONFIG_MODEM_ CELLULAR_APN` ? Or will it auto detect? Does it depend...
Hello,
We are using the NPM1300 with a lithium polymer battery that has integrated cell protection.
When the battery reaches the over-discharge level due to prolonged...
I got the following setup: nRF52840 - GenOnOffClient (Light Switch Sample) Publish to Group 0xC001
nRF52840 - GenOnOffClient (Light Switch Sample) Publish to Group 0xC001...
Hello!
I have a complex issue that I am trying to brainstorm. The task is that I am trying to receive a file over the air and be able to serial flash my STM32U575xx.
...
I have customed my own nrf54l15 board and run peripheral_uart demo successfully. Then I tried to measure its current while running peripheral_uart demo, it was up to almost...
Hi,
I've received the nRF54L15 DevKit and tested the power consumption during sleep Testproject in GIT: https://github.com/marcel-cd/nrf54l15dk-powertest
The result was...
