Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hello Experts,
I my main.c, I have defined my own TIMER1_IRQHandler() and when I build the code I get the error
Rebuilding 'timer_pca10100' from solution 'timer_pca10100...
i use ble_app_uart example code.
i have some problem that sometimes MCU can send data to application. but sometimes MCU can't..
ex) Success : 0x01 0x02 0x03 0x04 0x05...
hello i'm using nrf52840 dk board for communication with windows pc.
in nrf 52840 datasheet usb max speed is 12Mbps but my project based on "usb_cdc_acm" usb speed is 4Mbps...
Hi, we have project AoA direction finding. Firstly we have nrf5340 dk kits. Also CoreHW ANT3 2x2 matrix antenna kit. I run the direction finding connectionless demo on nrf5340...
Hi,
I am working with USB mass storage example from the SDK, and it works perfectly with the DK. Now I am working on my integrated PCB, and the same mass example doesn't...
Hi,
I am trying to get both the 802.15.4 stack and the BLE AoA stacks to run concurrently on an nRF52833.
Looking at the documentation here , it appears that it should...
Dear Sir/Madam,
I am trying to enable FEM support on zigbee/light bulb, and want to SKY66112-11 FEM working on Receive bypass mode. I set all pins at proper setting at initialzation...
When performing DFU with the same Android device + nRF Connect on the same target device, the speed becomes significantly slower on Android 15.
The attached image captures...
Hello. The visual study code uses toolchain v2.7.0, SDK v2.7.0 I'm trying to test the saadc example (in modules/hal/nordic/nrfx/samples/src/nrfx_saadc/) in "creat a new application...
Hello Nordic Team,
Our existing device using NRF52840 QIAA, we are plan to replace the QIAA package with CKAA package for size reduction. After I went through the SPEC,...
I´m testing the nPM1300 in a custom circuit with Zephyr on an nRF52 / nRF53 attached to it. It looks like the IC isn´t charging a battery. For testing I use the nPM1300-EK...
Hello,
Can I use in production nrf52840-DK as programmer to program E73-2G4M08S1C module on custom PCB?
What should I do to make the program code unreadable?
Hello, I need further assistance with the issue in the mentioned ticket ID, as it was closed by mistake. Could someone please reopen it so I can continue the discussion? ...
nRF52833-based board, software is based on Zephyr and Nordic SDK 2.1.2. Using Tag 2 type driver library, nfc_t2t Occasionally, when NFC coil is tapped, we observe one of the...
