Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hi,
I am working with Thingy53 using the ESB (Enhanced ShockBurst) library. I have my basic app running with multi-point comms and power control. This was done without using...
Hello,
We have a product which is a custom nRF52832 board, nRF5 SDK (didn't have time to upgrade to nRF Connect SDK), s132, BLE.
We used to call delete_bonds() function...
I‘m tring to run nRF5340 Audio applications with two nRF5340 Audio boards, following at: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.6.0/nrf/applications/nrf5340_audio...
I'm using the async API for UART and I have noticed that, shortly after initialisation, I receive a single character with the UART_RX_READY event. This character is 0xff ...
Dear all,
I kindly ask you what is such warning that arise in building the configuration for the NCS example, please point me to better understand why arise and the related...
I now have a 52833 board, my question is what is the difference between it and 52832?
Are they very different?
Which protocol stack does it use?
thank you
Hi
I can't find any info regarding a cut off feature for the nPM1300 if the battery voltage is to low.
we are using a battery with PMC but that is meant as last resort...
I am using nRF52840 boards. I have one query.
I understand from your documentation that MPSL schedules the Radio driver to access the Radio. And BT ticker is for time slots...
Hi
I have flashed the unit with the Vysor flash file at Vysor Dongle · koush/vysor.io Wiki · GitHub The unit is now dead and has not recovered so I am returning to amazon...
I was planning on writing firmware for the nRF52840 chip (AKA System Controller) on the NRF9160 DK. Primarily it will use BLE and serial communications over some of the pins...
Hi, I am using nRF52840 and nRF Connect SDK V2.6.0
I want to send 7000 bytes of data using USB at a time. Now I am able to send only 1024 bytes at a time. I modified USB...
I'm using the nRF52+SDK11.0.0+s132. I'm developing a system that streams BLE notifications to an Android app at ~53kbps (40B/6ms). I have the connection intervals set to 7...
Hi,
I have a system I am redesigning to use the npm1300.
It has a rechargeable battery, about 3-4 weeks per charge, connected to an nrf9160.
The current system...
Hello,
I had to build the https_client sample again to compare some behaviors on my application and as I flash it to nRF9160 I am having a cyclical error as below:
...
Hello!
We decided to switch from NCS 1.8.0 to 2.7.0 for our products and at the beggining of everything, noticed something very strange.
Prepared very simple example of...
