Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
I am using an N52811 QFN32 on a custom board.
I modified the SAADC sample as follows and ran it on this board. (3.0V was input to AIN2.)
However, p_event->data.done...
When I launch the Power Profile in nRF Connect for Desktop, the following log appears, and it cannot connect to the PPK:
The versions of each application are as follows...
As the question explained. I want to know if we can implement all three zigbee roles viz, Edge, Router and Co-Ordinator in a single project and can be able to switch them...
Dear Nordic Team,
We are working on a solution where we want to only connect to a certain device if it is a known device and not accept any random requests.
We believe...
Hi ,Nordic
nrfx_err_t nrfx_pdm_buffer_set(int16_t * buffer, uint16_t buffer_length)
I wonder the buffer is PDM buffer or PCM buffer ?
also want to know that how...
Dear support team, The customer used ncs2.6.0 to run on nRF52840 to make matter over thread smart door lock. When stress testing the switch lock (repeat: password unlock ...
I 'm using zephyr to create a custom nrf52832 board .
I 'm using the Devicetree Visual Editor .
Any idea why I can 't select this specific display controller ?
The datasheet...
Hello, As for my peripheral BLE NUS service under NCS 1.9.2, when I search and connect it from my Windows PC running nRF Connect for Desktop BLE Standalone 4.0.0, I found...
I am sending data from iOS to a nRF5340DK. I have some code showing the TX/RX MTU Size:
Which shows: Updated MTU: TX: 527 RX: 498 bytes
But on the iOS/Controller...
Hello!
As stated in the subject, when I followed the steps in the chapter of running OTBR using Docker ( https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/protocols...
Hi, am using the nrf52dk with nrf52832, nrf coonect sdk 2.5.1/ toolchain 2.5.2 and am building a prototype to aquire the signal from the ckp and cmp sensor in the car when...
Greetings,
We switched from nrf9160 to nrf9161 and got the first boards manufactured. NRF9160 has been working fine but we wanted improved GNSS functionality on board. ...
Hi all,
I have plenty of experience with the Old SDK, IAR/Keil/SES, nRF51, nRF52, Soft Device, etc. However, I'm new to the nRF Connect SDK, VS Code and nRF5340. I've successfully...
Please let us know which PINs of nrf5340 are used by BLE stack and which pins are used by peripherals like UART0 and UART1? We are converting our code from nrf connect V 1...
Hello,
We are evaluating MCU's for a low cost Central device that is extremely cost constrained. The nRF52805 and the nRF52810 both have the same RAM (24 KB) and FLASH ...
