i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Good afternoon,
I am trying to send some analog data from a function generator to my nRF7002 DK and visualize the output in Putty. I use printk to print the values and I...
Hello.
I modified multi-nus central example to connect with four peripheral devices. I don't use uart at all, I don't need it, I don't need routing, I just send 16B frames...
Hi!
I am confused regarding NUS, L2CAP, ATT and GATT.
We are using NUS with data length extension to communicate between two nRF52840 boards and want to maximize packet...
Hi, here in the documentation ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/config_and_build/board_support/processing_environments.html ) for the latest...
I have been trying to interface the Witmotion WT901 sensor with the nRF5340 using the I2C interface. I have previously run the exact code on the nRF52DK and it was working...
Due to the allocation of Flash resources, only 100KB ROM for the app , and if we use Keil, we will have about 20KB of margin for additional code development, but we have to...
I'm new to Zephyr and have inherited a project that uses the stm32 h747 disco board. The last build shows:
Memory region Used Size Region Size %age Used
FLASH: 363268...
I'm trying to download a largish file (~167KB) via HTTP/TCP/IPv6 but the modem crashes every time around the same point during the download. It's spits out error 122, which...
Hi,
I just ran into a strange issue and traced it back to a KCONFIG problem... It seems that if I have BOOTLOADER_MCUBOOT and SECURE_BOOT configured "y" I end up getting...
Hello,
I' have problem with CMAKE and Zephyr in VSC. Please, see following error:
[main] Building folder: blinky_13
[main] Configuring project: blinky_13
[proc...
hi,all
I Need add many characteristic with notify in one service,and I wish it can send notify to the phone once the phone enable cccd.
1.tx_handles can work,buf rx_handles...
Good day,
I am developing app by SDK 17.1.0, including ble_nus and ble_hid, I would like to imply fuction to switch between ble_nus and ble_hid, due to some difference configuration...
Hi!
I am trying to subscribe to the power management events that correspond to the following log lines (which I can clearly see in the log):
I have been trying with this...
Hello All,
I'm currently now on the initial phase of development and i wanna to stream 2xIMU data through SPI as for now if i connect only one IMU as Follow
P1.15 SCL...
