Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi Sir,
We are the first time to use Nordic BT MCU for our product, we have a trouble to select the MCU between nRF52833-CJAA-R vs nRF52833-CJAA- B -R. Sales told us there...
Hi, we are currently trying to reduce the power consumption on our product that uses an nrf52810.
An 1k pull-down resistor has been used on the SWDIO pin, but I don't really...
Hi,
I am using nRF52833 & nCS for an application development,
I am facing a curious issue where, if i enable printk in nCS build, I am getting SUCCESS on calling device_get_binding...
I'm trying to join two programs that work well by themselves, a saadc program that shows the force sensor value in the serial, and a BLE program that turn on or off a LED...
Hello every body,
I'm now utilizing the nRF9160 to develop several products based on SDK 2.0.0. In my program, I must produce SBOM.
This link below has some information...
I am on project using nRF52832 WLCSP.
What's the pin assignment for SWDIO pin? I want to read the input of SWDIO (as indicated in datasheet it's Digital I/O) and can it...
Dear Concern,
We were developing one of our products using nrf52840. We previously used the nrf-52840 USB dongle for the product. Now we were moving to nrf52840 chip based...
Hi,
nRF5340 + nRF21540, NCS2.0.2, VScode
i follow Working with RF front-end modules — nRF Connect SDK 2.0.99 documentation (nordicsemi.com)
how to disable TX_EN? i only...
Hi,
I am using SDK 16.0.0 and nRF52833. In which TWI (master mode) is not working.
Pressure sensor is connected over I2C. (NRF_DRV_TWI_INSTANCE(0))
Previously I am...
Hi to all!
I'm trying to use the same GPIO to wake up the nrf52810 from system off and also use it to execute some functions. I have this code that is based on the example...
I'm trying to load a program to a custom pcb with a n52832 chip, but shows up this error in the Programmer: Failed to load readback protection status: async task failure for...
Hello,
I am working on a project that modified from ble_app_uart_c, with sdk v16.0, softdevice S140
In my case, I defined an event observer by
NRF_SDH_BLE_OBSERVER(m_ble_observer...
