I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
We are writing a custom flash loader and I am not sure about the size of the flash and the address.
In the datasheet it says the device has 192kb of flash. But there are...
I am trying to determine if there is a process or equipment to bulk or automate provisioning of units using an NFR9160 transceiver prior to shipment. Will need a means to...
I developed a product with 9160 and stored some data in NVS. The product can run normally at the beginning, but after a period of use, when the device was restarted, I found...
Hello,
I am using NRF52833 with Soft Device S140, SDK 7.2.0.
according to sd_ble_gap_tx_power_set() API
"* @note Supported tx_power values: -40dBm, -20dBm, -16dBm, ...
Hi,
Out of testing large number of boards, observed one board is not working. When tried to debug, found this weird problem. Code is stuck in LFCLK init part.
main() ...
Hello, I developed for my customer, a ZigBee coordinator in last 2019, using nRF5 SDK for Thread and Zigbee v3.2.0. Now my customer has this issue: - End Node connected via...
app_button_init() and app_button_enable() returns NRF_SUCCESS. But event handler of app_button isn't called.
log messages of nRF52832 device is as follows.
00> <debug...
Hello,
Somehow my thingy91 is no longer working so I decided to flash it from the beginning.
I put it in MCUboot mode ( holding SW4 and turning on the device)
in Programmer...
Hi, I'm new to the NRF Connect SDK, as well as nRF Connect for Desktop.
I have a nRF52840 Dongle and a nRF52840DK.
The nRF52840DK worked well. But I could not program...
Hi Team,
Currently, we are working with NRF52840.
We have developed an android app to communicate with NRF52840 which has the functionality of an automatic connection...
Hello all,
I am porting the code from the nrf52dk to the nrf52820 based module and so far so good!
However, I can blink the LED on certain pins while not on the others...
Hi,
I am developing the nRF52833 DK with NCS v2.00.
I have implemented a service to display RSSI. I have setup the service according to the instructions provided by Nordic...
Hello everyone, I have an oxygen sensor"Gasboard-7500H" i need to read purity and flow with UART communication, this sensor works perfectly with Arduino and display corrects...
Hi,
I am developing an embedded system that uses Bluetooth communication and would like to manipulate certain Bluetooth characteristics such as TX power and RX sensitivity...
BLE Device
- nRF Connect SDK: v2.0.0
https://github.com/NordicSemiconductor/IOS-DFU-Library
This library doesn't seem to support the new nRF Connect SDK.
Which library...
