Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
HI, I am start use NRF52840DK(rev3) to devlopment usb application，but jlink always show this information
I try to use 'nrfjprog --recover' to disable read protection,...
Hello Groups,
I'm trying to send I2C/twi data from nRF52832 using the Nordic development board with nRF Connect SDK 1.9.1.
Based on the sample project ble_app_uart, I...
Hi nordic:
As shown in the figure below, I see that the BLE protocol standard mentions the ScanReq backoff mechanism. Does NORDIC implement it?
jermi.jin
thanks!!...
Hi,
The central_uart sample hardfaults when bt_enable(NULL) is entered. I can use the debugger and step over the first couple lines but stepping over bt_enable causes a...
Hi
I have integrated the example code for mesh dfu provided in the nrf mesh sdk5 in my main application . I have followed all the steps mentioned in this dfu guide. The...
Hi,
We have a working LwM2M device based on nRF9160 and NRF Connect SDK 1.1. When we run with a short register-update period (30 seconds) on a NB-IoT network it works. When...
Good Morning,
I would like disable passkey in the example "peripherals_hids_keyboard". I am able to connect with differents hosts (2 smarts and i computer) but I'm having...
On SoftDevice S140(V7.2.0)
ble_gap_adv_report_type_t status has four types.
BLE_GAP_ADV_DATA_STATUS_COMPLETE BLE_GAP_ADV_DATA_STATUS_INCOMPLETE_MORE_DATA BLE_GAP_ADV_DATA_STATUS_INCOMPLETE_TRUNCATED...
I am using nRF Connect SDK with VS Code on Ubuntu 20.04. I have installed SDK using the nRF Connect for Desktop and Toolchain Manager.
When I start VS Code I get the following...
Hi, I am trying to see the connected devices by executing the "lsusb" command, these are the steps I followed:
1.- Connect USB / swith NRF power Source to USB:
2.- Click...
Our development environment extends the NCS for our 9160 and 52840 hardware. To create a command line build environment in v.1.x.x, I was able to leverage the env.cmd file...
I have migrated an application based on the peripheral uart sample, running on a Fanstel BT40 board, from nRF Connect SDK v1.6.1 to v2.0.0. The application receives one line...
Hi,
I am trying to send data to a http server, and are trying to error handle. I am looking trough the documentation on the send() funciton in the socket.h library, but...
Hi,
I have an issue with interrupts on TIMER1 on nrf5340 NETCPU. My setup involves 2 timers that are linked via DPPI, TIMER2 counting microseconds and TIMER1 counting milliseconds...
