Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
In my application, I need to use the nrf52840 for both BLE (as the controller) and ShockBurst. Specifically, it's the nrf52840 on the nrf9160 if it matters. I'm using the...
Hi Team,
We are working on nRF52840 SOC with BLE functionalities.
We need the mechanism for to find out the BLE or BLE Stack is in Hanging state before the processor is...
Hi,
I'm trying to build a proof of concept for a BLE gateway that captures data from BLE sensors and sends it to the cloud via LTE-M connection. I'm hoping that the gateway...
problem description:
hi, I just got a PCA10040 development board with which I plan to learn about nrf connect SDK.
so I try the common BLE peripheral demo,but I 've met...
In order to add the BLE DFU service, I need to increase the GATT table size and therefore memory as mentioned here: .
However, when I tried to increase the file ble_app_uart_gcc_nrf52...
Try by changing the RAM size but it didn't worked.
<info> app_timer: RTC: initialized. <error> app: ERROR 4 [NRF_ERROR_NO_MEM] at :0 PC at: 0x00000000 <error> app: End of...
Hello, I have managed to get two NRF5340DK linked and measured their throughput. Now I need to change their Output Radio Amplifier Power to test again. And then I also need...
Hello Nordic Team,
I have an issue on one of my 10056 DK. The DK is connected to a development PC, appears in device manager as a Jlink CDC UART port, and as a mass storage...
In the Zigbee framework, what is the purpose of the return variable from zb_osif_sleep() ? The "documentation" for Zigbee seems to implement a "guess and figure it out for...
Hi,
I'm following the ble_template example on my custom board. I'm having an issue with waking up (soft reset) the device from sd_power_system_off. I can power off the system...
Hi ,
We are using s140_nrf52_6.0.0_softdevice, SDK 15.0.0 for NRF52840 chip. Does this sdk and soft device supports extended advertisement?
I could able to enable this...
I use both nrf52833 boards to do AOA test.But i use thr antenna array board of silab.The board are 16 antennas.I use the NCS version 1.9.1.
The next is my device stcture...
Hey All:
I'm trying to create a new app in VS Code. I've got the latest v2.0.0 SDK. I get the following error:
[west]: FATAL ERROR: Malformed manifest file: /home/ebolton...
hi support team,
customer have one question about nrf dfu with serial:" how to disable flow control for 2 wire uart".
previously we have one ticket :"https://devzone.nordicsemi...
Hi,
I'm using nrf52832 DK with SPI slave mode to read 600 bytes from other nrf52832 DK with SPI master mode but i can't receive more than 255 bytes buffer.
If you know...
