Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi,
I using the radio test on the nrf52840 for RF verification, but now we want to reduce the latency from 8ms to 1ms.
Is the radio test project can modify the latency...
I have Raspbery pi flashed with nordic alpha 4.1.0.1 image + nrf52840 dongle in NCP design .
As an end device I have EFR32 MG12 WSTK flashed with OT-CLI-FTD code and connected...
We are using Zephyr RTOS running on a nRF9160 MCU. One requirement of our project is to run a local HTTPS webserver on the target. Our investigation showed that the recommended...
Hello,
Now, the ROHS and Halogen free report of nrf52832-qfaa is out of data when downloaded from the infocenter.Our customers request to provide the unexpired versions...
Hello All,
I am new too BLE so sorry in advance for this generic question. I am trying too get Temperature data from sensor while in connection state(Phone connected). Also...
Hi All!!!
I develop combine (NUS) & (NUS_c multilink) device
nrf_ble_gatt: sd_ble_gatts_exchange_mtu_reply() returned NRF_ERROR_INVALID_STATE
What is this and how...
Hi, I am working with nrf9160 using Segger Embedded Studio and J-Link. I could build the code but not able to download the application.
I am getting error as CPU is not...
Hi ,
i have programmed my NRF51 sniffer dongle (PCA10031) using nrf programming app and I could see something like this in below pic. Is it expected output in the programmer...
Hi,
this at-command provides the cell ID of the connected cell, but only physical cell ID for neighboring cells. Is the cell ID of neighboring cells limited by the LTE protocol...
Hello all,
I want to build a two-directional communication chain with several nrf5340-boards. Therefore, every board needs to be able to receive, to analyse and to send...
I am trying to make a function execute every 1 second using the provided example on the zephyr documentation, but i am getting the following error: "expected declaration specifiers...
Dear Sir/Madam
I used sample project uart_pac10040 loopback. It works with not define ENABLE_LOOPBACK_TEST. However, if define ENABLE_LOOPBACK_TEST, and wire the pin RX_PIN_NUMBER...
Hi,
I am trying to add an IPv4 HTTP client post-action into the asset tracker v1 app, I have a couple of questions.
I am looking at the http_client and DHCP client samples...
I started my Bluetooth application based on zephyr examples found in nRF Connect SDK v1.4.1(C:\Users\...\ncs14\v1.4.1\zephyr\samples). Now I need to add custom service for...
Hi,
I have the following setup of devices, that I want to connect over BLE:
1.) A device X, that executes commands from a smartphone and a second device Y and also sends...
