Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
hi,
i am using nrf52832 devkit and max30208 temp. sensor. i am not getting updated data. iprefer this link for i2c address.( https://os.mbed.com/users/cyberjoey/code/OT07_I2C_GUI_Firmware...
We are implementing a protocol using the softdevice s140 multiprotocol API. The protocol is always listening, but occasionally transmitting.
To manage this setup, we request...
Hi,
I am exploring the idea of removing the JTAG port from the PCB to make it difficult to maliciously change the firmware on the field. I have the secure UART Boot-loader...
Hello
I am developing a firmware for nrf52832 using buttons like if I continuosly press my button for 6 seconds it will go to active mode from sleep mode and have been using...
Dear sir,
I have a light sensor connected to P0.04/AIN2 on 52820. How can i get the change of voltage?
I use the COMP, and has enabled COMP_ENABLED in sdk_config.h, compiled...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
We have a standalone application with no SDK integration. We would like to have the possibility to do OTA Updates via BLE and maybe introduce BLE support later on.
So for...
Hi,
I am trying to run IPSP example from nRF Connect SDK 1.4.2 IPSP sample (v1.4.2\zephyr\samples\bluetooth\ipsp). The "ping6 -I bt0 ff02::1" command is working fine but...
Hi, I am using the nRF52840 DevBoard with SDK 16.0 and Mesh SDK 4.1 and am building on the light_switch_client example.
I am trying to change the publication address by...
Hi,
I'm using nrf52 with s132(v17.0.0).
When I connect nrf52 with my phone, there is error like this picture.
And, the code is
When the buffer is filled, then...
Hello.
When I use NRF_SAADC_INPUT_AIN7 in SAADC, I get an error in calling nrf_drv_saadc_channel_init(). Looking at nrfx_saadc_channel_init() in nrfx_saadc.c, it seems to...
Hi,
In order to determine signal strength we parse the AT+CESQ response and regularly get +CESQ: 99,99,255,255,255,255 (the final number being the strength), but the connection...
Hi,
1、If I want to devlop zigbee with nRF52840, whether the only one sdk series is `nRF5_SDK_for_Thread_and_Zigbee_xxx` ?
2、Can BLE coexists with Zigbee in a nRF52840...
