But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello guys,
We are developing a device that will based on nRF9160 SiP. We use nRFConnect SDK v1.3.0 . The goal would be to connect to AWS IoT through MQTT and exchange messages...
Hi,
In one module of an application I would like to statically declare a large buffer in SRAM: static uint8_t largeBuffer[65536];
The application fails to link with the...
Hi,
I have been implementing the GPS on my thingy:91 with the firmware v1.2.0
I'm able to do a cold start and get a FIX is if in do not move the board for around 100...
Hello，I am using SDk14.1.Sometimes w hen I send data to nrf52832 via serial port，the code prompted me "APP_UART_COMMUNICATION_ERROR".And t he value of the ERRORSRC register...
Hi, I am trying to perform an OTA DFU of SD + BL on nRF52840, upgrading the SoftDevice from 6.1.1 to 7.0.1.
I have been able to do a DFU of application only, and it works...
Hello everyone. I have the following issue: I would like to connect some Nordic Thingy:52 nRF6936 devices in a mesh network, using the application nRF Mesh . In theory, the...
Hi,
We are in the development stage of a project using NRF9160. We would like to know which one is the stable version of NRF connect SDK. In the , git we can see tags like...
I have a non-secure app targeted at the nRF9160-DK platform and use SPM as the secure app. I can apply a device tree overlay to SPM to enable peripherals from the non-secure...
Hi,
We are creating an application that requires LTE connectivity, GPS and communicating to a server using HTTPS. We used the HTPPS client example as a starting point and...
Hi,
I'm quite new to the nRF environment and am trying to run one of the nRF5 SDK examples (ble_peripheral -> ble_app_uart -> pca10056 -> s140) on a custom bord with BT840...
Hello everyone, I have a problem I am trying to merge to project using I2c and Uart, So I copy the code from the uart example in the sdk.
I can read on the debug terminal...
Good afternoon, I am trying migrate from ARM compilar 5 to 6 some examples of the SDK 16, but i have some problems with it. I was wondering if a version 6 compatible sdk would...
Hi
I am using the provided example ble_app_queued_writes to send 256 bytes in each call.
It is taking around 13 seconds to transfer 3136 bytes:
12 calls of 256 and one...
