Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I am currently following the tutorial for creating custom services ( https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial ). The only differences to this...
Hello Nordic,
I'm working with NRF52840 (with SDK 16 and softdevice s140 7.0.1) in my project. I need to work with another chip through SPI. This chip is the master and...
Hello,
I have one more questions while doing test with SAADC, UART.
When I was tested the SAADC pin connect with ground, the negative value occurs.
So, I changed the...
Hello,
i've built a basic Thread network with two nRF52840 Nodes running the CLI example and a RasPi with a nRF52840 RCP as BorderRouter.
My Question is:
Whats the...
Hi.
Hope you are well.
I want to send data from nRF51822 to nRF24L01+. I used the esb library to configure the nRF51 and I just change the settings as I want ( some settings...
Hello~ I have previously written related articles. But I don't get the answer I want, so I ask you again. Use the toolchain manager to use ncs 1.3.1. The error as shown in...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hello guys!
We are workng with nRF52840 SoC and SDK v17.0.2.
Custom BLE Services and Characteristics are needed to implement in our device. Before starting that implementation...
Hi,
In our design, nRF9160 is powered by a LiPo battery, making VDD = 4.2V in a "fully charged" case, and VDD=5V in a "lipo is charging" case.
We would like to be able...
In trying to use a private key file to sign the application image I'm running into an issue with the PEM file. I created a PEM file using the following command:
as documented...
Hello colleagues,
Mi name is Daniel and i'm trying to develop a software application that let me calculate the PER (packet error rate) of a bluetooth transmission.
The...
Hello Team,
I am working on a project in which I want to used pdm microphone with nrf51822 xxAA and i am using keil u5.
1) So I have picked uart over BLE example from...
Hey there,
I am new to the community and I would like to looking for more than one cell. As I readed in another thread, it was possible with %NBRGRSRP a few month ago. ...
I was looking through documentation and I noticed that in OPS v0.7.1 the cold start was stated to be -144dBm. In PS v1.1 it calls out -142dBm. Can you explain why they are...
