i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hello,
I have configured MQTT over TLS to connect to our broker. Everything works great except that the modem stops reconnecting to the broker after exactly 22 connect-disconnect...
Hi, I'm trying to run the nfc_pairing example from the master branch (1.3.99) of NCS. I've successfully built the example in SES and loaded it onto my nRF52840DK, but the...
I'm wondering how BLE signals are handled at the layer below the scanning module. Namely, suppose there are hundreds of BLE modules that are all advertising nearby. How does...
Hi
We are developing a 70 x 70mm PCB containing a nRF52840 for BLE/ESB and a second module for WiFi/BT.
We have no mechanism to avoid transmission of the WiFi module while...
Hi. Sorry, can't find the answer on the forum on my problem.
I am using:
nRF52840 DK
Segger
MacOS
Fanstel BC840 module
I have a project that flashes to Raytac...
Are there any examples of how to enable and use coded phy long range with the nRF Connect SDK? I have the nrf52840DK and would like to create an advertising example to test...
Hello,
In my current project designed around nRF52840 incorporating many peripherals (limited power budget) and many central devices. Each peripheral can connect to any...
Hi
I am using NRF52810 with Softdevice S112 7.0.1 and SDK 16
I want to ask about the behavior of the softdevice notification queue on disconnect. I have seen these two...
Hi .thank u for reading this .First sorry for my english. This is the story:
I try to make a flexible mesh using multi nrf24l01+ more than 10 nodes. I searched so many topic...
While running a Scan in nRFConnect 4.24.3 on Android 10, Nokia 6.2, I see the first Advertisement from my BLE Device. That device advertises different sets of ScanData over...
Hi ,
I am working on a project where i need to publish wifi scans over ble , issue is that when ever we try to send data over it either send or not sent to avoid data loss...
Does Nordic have some solution for this? Device would be a WiFi+BLE gateway, which runs Linux, and can support advertising scan for at least 300 beacons, and have Ethernet...
Hi, I am running into issues where the nRF9160 (in NB-IoT mode) does not seem to handle cell changes reliably. I am using modem firmware mfw_nrf9160_1.2.0 . I made a simplified...
Hi Nordic guys,
I'm trying to create a pin pairing between an NRF52 DK and iPhone.
I've created this function to do that:
I've added that function in the ble_peripherical...
