Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I'm developing a product that use the Nordic UART service over BLE and need something similar to a USB serial port, except with NUS. Is there a Windows 10 driver that works...
Dear Nordic Team,
Thanks for supporting.
Currently i am working in Mesh network. My application is Single Client control 100 Server Individually . Same like this https...
Dear Nordic Team,
Thanks for supporting.
I am new for mesh network concept. I want to control individual device in mesh network (May be more than 10 device). I have tested...
Hi,
I have a project that has a bootloader based on the SDK15.3 secure buttonless DFU example. During pre-production testing, the need for downgrading the app came up. So...
Hi,
I just wanna start off by saying I know there a lot of similar posts to this one here on the dev zone, but my problem with them is that none of them (from what I've...
Hello,
we're just planning to deplay our first border router for bigger in-house installations and wan't to use a USB-Dongle with the nRF52840 as NCP with the Openthread...
Hi All,
We are working on zigbee protocol and wants to replace the existing setup with nRF52840 . We have some below queries need your answers on the same to go ahead on...
Hi
I'm developing an application that is pretended to run on an nrf52810-based custom board, The code is a modification of the blinky example from the SDK 15.0.0, and for...
Hello,
on my previous project i rellay enjoyed the offline documentation of the sdk (SDK14.2).
Since we are using the Thread-SDK now, I haven't found a offline documentation...
I'm using SDK 15.3.2 with SD 132. SES and the 10040 DK.
I'm not clear how NRF_LOG module and the new serial port library is support to work together.
I can easily make...
Hi Nordic!
In our design we see variations in the rev C lot we have received. We are using the VDDH REG0 regulator. Some of our ICs turn ON with no problem. And even when...
When I scan BLE device at nRF UARTv2.0 App in Android4.4, it is appar device name(Ex:Nordic_UART) and 6 byte device address(MAC address?).
I want to include mac address in...
The button is connected to ground directly ,and without external pull up resistor.
I found it consumes too much current when using internal pull up resistor,but when I use...
According to at client demo, LTE-M1 is the default mode in firmware mfw_nrf9160_0.7.0-29.
Modem work mode will be LTE-M1 after every reset even you changed to NB1.
I...
