Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Our project is built wit NRF Connect SDK 2.9.0. For the UART we use nrfx_uarte library directly.
RX works perfectly, but TX is working only in blocking mode. If I call ...
Hi,
I designed a custom NRF52832 board and need to connect it to an ESP32 board. I soldered five boards for testing and also have an NRF devkit.
However, the ESP32 only...
My platform is the NRF5340 , coupled with 32MB of external flash , so I have plenty of external storage available. However, there's a risk that my project may eventually outgrow...
Hi there,
we're currently in the process of changing our hardware to use the nRF54L15. Since all the security regulations are getting stricter and stricter and the support...
I'm looking at Product Specification v1.2 - Reference Circuitry Configuration 2 where BUCK2 is not used. The schematic shows the output VOUT2 is tied to VSYS in this case...
Hi Nordic Team,
I am planning to develop a Matter-over-Thread end device (sensor) using the nRF54L15 , which will be battery-operated . To maximize battery life (minimum...
Does anything exist yet? The datasheet only contains a preliminary matching network and says will be available when the chip enters mass production, but nothing is available...
Hi,
I'm trying to use the HCI UART sample to provide Bluetooth support through UART. At first I want to test it between two Nordic Boards, but later switch to another MCU...
I tried used Nordic's UART service implementation as a starting point and everything works but I can't figure out where the string "Nordic UART Service" from "nrf connect...
I have loaded the Quick Start Application using nrf connect for Desktop after following the instructions. I get the error as per the attached file on the Serial Terminal....
Hello,
We are trying to test our custom board with nRF9161 in a new location, so we bought local SIM cards (Yettel, Serbia) here. These are not special nb-iot SIMs, just...
Hello all, First, thank you for the support and community here, which is very helpful. I have been developing a device using the XIAO nRF52840 device. (link: https://wiki...
Is there a way to modify the distance measurement sample code to where it is intended for one transmitter and multiple receivers versus between just two devices? I am trying...
The workaround says:
" Trigger TASKS_PLLSTART before TASKS_XOSTART is triggered and trigger TASKS_PLLSTOP after TASKS_XOSTOP is triggered."
I would like to start HFXO...
Hi,
I am running into a really strange issue where setting both CONFIG_NRFX_PWM0=y and CONFIG_NRFX_PWM1 =y in prj.conf gives me the following build errors while using mcuboot...
