Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi folks!
I'm working with a couple of nrf52832 on custom boards. I'm trying to implement a procedure for firmware updates. I've already played with the examples from the...
I have found many questions regarding passing bonding information from the application to the bootloader (e.g. https://devzone.nordicsemi.com/f/nordic-q-a/34497/dfu-with-bonds...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
I am using "twi_scanner" example code on Development kit. I connected HDC2010...
Errata for nRF52832 Rev 2 version 1.2, errata item 20, RTC: Register values are invalid, has a recommended workaround that i'd like to ensure i've implemented correctly -...
Hello,
I have a project that does what the title states, create a Mesh Network using the Nordic USB Dongles then provision a smartphone using GATT to access the Mesh network...
Hi All,
I have used eeprom(AT24c512) and spi(Winbond 25q16) in my Product.Usually all work working fine But sometimes my memory Behaves like volatile ;sometimes My Memory...
Building ‘secure_dfu_secure_dfu_ble_s132_pca10040_debug’ from solution ‘secure_dfu_secure_dfu_ble_s132_pca10040_debug’ in configuration ‘nrf52832_xxaa_s132’
Linking secure_dfu_secure_dfu_ble_s132_pca10040_debug...
Hello,
I'm trying to update the SoftDeivce used on our product from s140 v6.0.0 to 6.1.1, but am running into issues. Per the release notes it sounds like no updates / recompilation...
we use 52810 connect with iphone6, then read the RSSI value, it will disconnect with the iphone6.
reconnect the iphone6 and read the RSSI value, it disconnect again.
we...
After doing some reading, I realized that the light CTL server model does not contain the generic OnPowerUp set message. It is contained within the light CTL setup server...
After import a project in to SEGGER and included paths of header files
While compiling i got the error like below
sorry, unimplemented: non-trivial designated initializers...
Hi, I am using a system where I am using nrf52832 nordic chip. I generate a custom ble service using this ' https://github.com/bjornspockeli/custom_ble_service_example ' github...
Hello.
I would like to use the SPIS module on the nRF52840 DK. I configured it by following the examples given by Nordic.
When I use pins P0.14 (nCS), P0.15 (SCK), P0...
I am using now SDK 15.0 and the value of APP_ADV_DURATION is set to 18000 (180 sec)
But I saw that fromSDK15.2, it is recommended to change the value to 0 in order to get...
