Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
I am currently using nRF8001 in my board (configured to connect - send data - disconnect - sleep every 30s cycle time). However, I am measuring about 140uA in average and...
Hello there.
I'm developing a custom board for the nrf52810 chip. I'm taking the reference files as a base for my own design, but I'm a little bit confused on which files...
Hi,
I am using nRF52840, SDK 15.0, softdevice 6.0.0 (toolchain IAR 7 on windows).
My application runs on FreeRTOS 9.0.0 tickless (NRF_SDH_DISPATCH_MODEL 2).
I have a...
Hi,
I want to get Battery ADC Value.
So. I simply used nrf_drv_saadc_sample_convert() function.
At first I thought it was the right value,
Later, I found that the...
Hi,
I want to get Battery ADC Value.
So, I simply used nrf_drv_saadc_convert()
At first I thought it was the right value,
Later, I found out the wrong value.
If...
Hello, Nordic.
I am working on an iOS App that uses a MPU9250 sensor to display a 3D simulation screen in my app. (It is same as motion control in Thingy52 App).
I...
Hi,
I am using PCA10028 development kit for sniffer with wireshark 3.0.1 using sniffer version V2.0 beta 3 . I am getting issue like "Encrypted packet decrypted incorrectly...
Greetings,
I was wondering why Amazon FreeRTOS demo wont work on nRF52840 DK. After following all the steps even building a bootloader on my board, my demo is running but...
SDK 14.0,
IC:NRF52832
I want to save some data in the flash via the FDS. firstly i write 3 records then the next I want to read them one by one according to the record...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image. I am using ‘ble_app_blinky’.
1) If I configure any GPIO as state change trigger...
I used Win 7.
I updated the nRF connect application to use with the nRF dongle.
The Microsoft wireless mouse and keyboard is shown like nRF Connect DFU Trigger. Also internal...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex?-M4F 32 bit processor...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image. I am using ‘ble_app_blinky’.
1) What is the difference between High-accuracy...
Hello
I am using Android and BLE communication with nRF52832 (BLENano2) now.
I am using SDK 15.0.0 with keil uversion.
Central is Android and peripheral is nRF52832...
