After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hello All,
I am working on nRF51822 using IAR IDE and nRF51 SDK 12.3.0.
Right now I am checking power consumption of device in ideal mode but right now it is higher. ...
Hello. I tried to understand MMA8652FC Acceleration sensor with 52832.
I don't know what means 16Hz, 8Hz, etc. under table.
I know just concept of High pass filer. that...
Hi, I want to use wolfssl library on nrf51822 and I'm in stuck.At first, I compiled wolfssl as arm-none-eabi ,then added the static lib to the project in segger studio.
...
Hello everyone!
I'm trying to build a project of gathering the information from several temperature/pressure/humidity sensors and sending it to one display.
Sensors will...
Hi, I've tried to set BLE power to max but an app error is raised when I use the sd_ble_gap_tx_power_set function. Parameters should be wrong but as far as I've read over...
How do I align UART transmission/reception with GPIO pin signaling low/high? I wanted to do this because BLE chip is receiving the Product ID & device name from microcontroller...
Hi there,
I was used IAR to compile my source, and combine with bootloader and soft device, and it was always work fine.
Now I have changed my compiling tool to SES IDE...
Hi there,
I am developing an application using an nRF52832, nRF5_SDK_12.1.0_0d23e2a and Softdevice s132 v3.0.0. The BLE part of the application involves sniffing advertising...
Hi All
On my NRF52 device I want to return my own error code after a mobile application (android) has written some data to my custom characteristic. For that I consider...
I am trying to get 2 of the nRF52840 dongles provisioned on a mesh network (client + server). (versions nRF5_SDK_15.3.0_59ac345 / nrf5SDKforMeshv310src)
I am using examples...
Hello
I'm using the NRF52832 with softdevice 132. My SDK version is 15.3. My platform is WIndows 10.
I am having trouble configuring the TWIS. I've followed the instructions...
Hi,
Here's the setup I currently have: nRF52840 SDK 15.2.0 s140 6.1.0 softdevice Secure Bootloader pca10056_usb
I'm trying to update the mbr_params_page (0xFE000) from...
I am new to the Nordic stack, and I have developed an Arduino outdoor prototype using an nRF52840 communicating with another ESP32 (BLE + WiFi) gateway. The project is used...
I use timer+ppi+pwm model.my init code like this
I use some code to close and open PWM ,like this
question:I use oscilloscopes to check PWM, I find that when I start...
Hi all, I want to work with Coded PHY on Bluetooth 5. I tried to change lines on mesh_adv.c file like below, but i getting this error : app_error_weak.c, 119, Mesh error 7...
