Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello,
We are considering bluetooth module of laird tech for our ongoing project, it has Nrf52810 chip. Please verify the below things Schematic: 1) this module has onboard...
Hi,
I am using nRF_SDK_15.0.0_a53641 and writing a program with keil.
I am now trying to write to the SD card at 1000 Hz (1 ms) by combining "fatfs example" and "app timer...
Two nRF52810 devices, one is PTX and another is PRX, use the ESB protocol.
This project is very demanding for the timeliness of data transmission, in order to improve the...
It would be very nice if the SoftDevice API Documentation at https://www.nordicsemi.com/DocLib included PDF downloads for each SD version as well as the current online HTML...
Hello Nordic community,
I'm wondering about how those BLE trackers (i.e. Tile , Trackr) work. Specifically, what kind of advertisement strategy makes sense for these types...
Hi
I am developing RX device to connect with Smart Remote 3.
The RX device system is Linux embedded. I need to run OTA function in Linux embedded to update SR3 F/W.
...
Hi,
I am using STM32F030C6 MCU with Laird BL651 module.
Keil-IDE v5, windows 7(64-bit) system configuration.
I need to get the sample code for the application development...
Hello, I have following problem.
My DK is not recognized by J-Link / nRFgo Studio.
I tried to reflash J-Link by pressing BOOT/RESET and then drag and drop J-Link OB...
Hi,
I would like to update the Device Information Service's (DIS) serial number characteristic to reflect the actual serial number assigned by our production equipment....
Hi, I am using the following setup: Wireshark 2.6.5 (updated yesterday) Sniffer 2.0.0-beta-3 (nrfsniffer200beta312oct20181c2a221.zip) nRF52840-DK (used by the sniffer) nRF52840...
I have a custom board that uses Nordic NRF52832 as MCU. For laying out crystals, BLE part and decoupling capacitors, I used reference layout from documentation.
32 MHz crystal...
Hi everyone,
My hw/sw configuration:
- nRF52840 - sdk 15.0.0 - softdevice: s140_nrf52_6.0.0
I would like to change the device name and update it in advertising packet...
Hi All,
I have been working on ipv6 over ble on zephyr RTOS to form mesh network.I have been successfully integrated "rpl_node"(which is in zephyr/samples/net/rpl_node)...
Hi guys,
I have very strange problem with the Android phone when connect with nrf51822.
After connection, I used update parameters to set the parameters on the phone side...
