Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
hello,everyone,
I use the Infocenter Guide , and
I changed my section placement marcos by the warning:
FLASH_PH_START=0x0
FLASH_PH_SIZE=0x100000
RAM_PH_START=0x20000000...
Hi, I am trying to interface nRF52832 with KX 124-1051 accelerometer sensor using I2C. I want to read the chip ID of the slave device. The SCL and SDA pins i used are 28 and...
Hi,
SDK15.2
Softdevice: S132 6.1.0 Device: NRF52832
Mobile phone:Galaxy S5 (Android 6.0.1)
I have a problem with the Galaxy S5 can't scan Bluetooth devices. During...
i am working on ble_app_beacon example and i am facing issues in evt_handler. basically i want to use on_adv_evt() function to put my device in sleep mode after timeout hence...
Hi team,
Our customer's application was mouse.
The requirement was to change BD ADDR and do bonding again after pushing the bonding key.
However , we want the device...
Dear nordic,
I check your ble app uart example in debug mode. After some time it goes to the NRF_BREAKPOINT_COND. nothing do in the eaxmple just loaded only why this going...
Hi.
I am not family with the Nordic product, this is the first time.
I just download "nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71.zip", because I plan to build my NCP...
Dear nordic,
I need a help to create a PWM. I want to create pwm of 10 ms time period and pulse width of 1 micro second. i created PWM of 10 ms time period but how i create...
Hi
I have nRF51802 and I have also downloaded Compatible SDK versions 12.3.0
I want to test out TWI scanner, but to support nRF51802 chipset where I have to change or...
Hello! I used nrf52832(SDK12.3,softdevice:v3.0) in my project, now i want to upgrade softdevice to v6.1.1 by DFU. I used the same private.key to generate zip package（App+SD...
Hi,
I have been trying for switching advertising parameters like m_beacon_info1[6]=0x00 to 0xff when button pressing.After 10 advertising ,the parameter back to normal as...
Hello everyone
I am a beginner in BLE.
I am working on nRF5_SDK_14.1.0-Nordic with nRF52840-PDK.
#define BLE_GAP_PHY_1MBPS 0x01 /**< 1 Mbps PHY. */ #define BLE_GAP_PHY_2MBPS...
Hi,
1) I would like to program softdevice + buttonless DFU + app in production using J-Link.I tried that but my device always runs bootloader only, in never jumps to app...
I'm seeing a softdevice assertion every now a then, it takes multiple days with the device running and advertising before we see it. Even though we have the DEBUG flag set...
