Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hey all, my QSPI woes continue. I'm trying write 4 bytes (0xDEADBEEF) of data to a flash chip, equivalent to the NRF52840 DK. I'm using PP4IO and 24 bit addressing mode but...
Hello,
I am using the NRF_LOG_INFO macro to print certain event results. I am writing a large chunk of memory over I2C. The operation succeeds but the log print is only...
Hi All,
I' ve successfully programmed an nRF52840 device with an application running with PHY_CODED modulation and I can scan it from my Samsung Galaxy S+. Unfortunately...
Hi, I'm running nRF5 SDK v15.2, and tried to run the led softblink example on port 1 of a nRF52840, which did not seem to work. I found a problem in low_power_pwm.c, which...
We want to use some device in the peripherial mode.
after the devices were bonded, for next connect I need to hide this advertise packet from air in the nRF Connect util...
We have a problem that we thought was isolated (affecting only one phone) until recently we started getting more phones exhibiting the same issue.
We are Australia based...
I can pair and bond as a Zephyr central via bt_conn_auth_register & bt_conn_security().
When the bond is successful I get a callback to cb_pairing_success(struct bt_conn...
Hello,
I am trying to read the internal temperature sensor using interrupts (SoftDevice is disabled). This is what I have:
#include "nrf_temp.h" #include "nrf_nvic.h"...
I am having hard fault when `nrf_sdh_enable_request` is called in BLE init. I am following BLE_TEMPLATE. I did not copy the solution, I am extending TWI example to include...
Hi,
I am trying to make a micro second timer count and I am using the timer driver from the timer example. However the timer init is failing in my code and I am not sure...
Hello,
I am using pc-ble-driver to write a desktop application interfacing with Nordic connectivity dongle. There is no automatic discovery module functionality so I have...
I am trying to just find what is this LE Secure Connection but can't seem to find anything basic. When i look at the lesc example, it look slike they simply turn the bit on...
Hello,
I am having a custom nRF52832-based central device - it works fine when connecting a single nRF52832-based peripheral (the both are based on SDK 14).
Now I need...
(added comment regarding intitialisation of GZP_PARAMS sunday 19 Aug)
I would very much like to use the gzp_dynamic_pairing package on the nRF52. Unfortunately I cannot...
hi, i am doing a project where i have to change adv name of ble device.
i am using nrf sdk 15.3.0 ble_app_blinky example for pca 10040e because it has all the things i need...
