Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi,
I have created a new project and am following BLE_TEMPLATE. I want to learn, that is why I am not copying and pasting the solution and modifying - its the last resort...
Hallo everyone,
I'm using Eclipse IDE for C/C++ Version 2018-12 (4.10.0), my OS is Ubuntu 18.04.2 LTS and my hardware is the NRF52840 DK. I'm using the GCC C and C++ Compiler...
Hi,
I already asked a similar question 6 month ago ( ticket ) but we never got a solution to this.
Now, after 15 month of development, our mesh-applications are almost...
hi I used light switch example in mesh SDK. i want put device in sleep mode if the device is detected sunlight (using solar panel). if again darkness detect means it will...
Hi,
I am working on a project where my mobile phone will be acting as a central device and nRF52840 DK will be acting as a peripheral device. I used the nRF UART and nRF...
I'm advertising a custom 128bit UUID for my service.
when I added the buttonless DFU service, the UUID in the advertisement packet got mixed, I ended up with the base uuid...
Dear nordic,
I have some doubts regarding ble nus service.
1. how many bytes i can transfer in one packet t a time from smart phone to nrf52832 viceversa?
2. Is it any...
We are using the Nordic nRF52832 and the nRF51822 in two different products. We seek to distinguish between these products and other BTLE devices with a scan using a dongle...
Dear Sir,
I am using nrf52832
SDK 15 and softdevice s132.
I have made a custom board using BMD300 module (nrf52832 based module).
I have takem the following pins...
Hi Everyone,
I am having this issue where i am not able to get ADC and BLE working together.
I am using external ADC and i am using BLE app uart as the base to develop...
I have a basic question regarding the interrupt priority. I want to know if the lower priority is triggered while the higher priority interrupt is served, is the lower priority...
Hi
I want to use GCC 4.9 2015q3 to build code on SDK v15.2 and v15.3 but it shows it cannot find 6 2017-q2-update and 7 2018-q2-update.
Checked Infocenter - Secure DFU...
Hello everyone,
I am trying to measure the current being consumed by nrf52840 using an external power supply.
Setup: I have connected 3.3V DC power supply to connector...
Dear Sir,
I am using nrf52832.
SDK 15
soft device s132.
I need to add the battery level also to the advertising packet.
Currently I have done code to read the...
