Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi,
I want to change value of serial number after dis init, I want to use sd_ble_gatts_value_set to set the new value, but I dnot know what is the right connection handle...
Hi
I try to flash the firmware from project light_switch_server_nrf52840_xxAA_s140_6_1_0 to nRF52840 dongle to build the Mesh Network with below modifications:-
Use...
I set the Thread network with 2 Dev Kits. I tested it using CLI directly. The network works.
But I can't observe topology on the monitor tool.
Reproduce path:
Follow...
Ive been working on this for some time and can not get two boards successfully communicating using the 125Kbps on the NRF52840. I am simply having one chip transmit advertising...
HI........ I am working on nRF MESH latest version , so i am here using three boards nRF52832 , i have set the character message in client side , when the button 1 is pressed...
Just continue my work on implementing LESC MITM on hear_rate_collector (Please check my development environment settings here as well).
Since sd_api_v6 on pc-ble-driver...
Developing IoT product using a module using Nordic nRF52832 - using their Shockburst protocol
Can ANYONE explain why we would need to be registered with the Bluetooth...
Hi,
I'm trying to make provision for AT command interface in my new nRF9160-SiP based design.
Couple of questions related to that:
1) Which UART (nRF9160-SiP pins) should...
HI,
Im using nRF5_SDK_15.3.0_59ac345 - SDK and two different bootloaders.
The first one is - sd_s140_bootloader_buttonless_with_setting_page_dfu_secure_ble_debug_without_bonds...
Hi,
I notice my dfu bootloader oversized after I merge softblink led feature into the example code. How can I modify the linker_section_placement_macros and the linker_section_placements_segments...
Hello,
Working on MAC. High Sierra.
got a 52840 dongle (but also a thingy and a devkit following the latest conference)
Trying to start at the beginning and build...
Hi,
currently I am trying to figure out how to disable the cryptocell hardware after enabling it, because if I enable it and then enter systemOFF, the system still draws...
Hello,
I am using NRF52840 Preview DK, I am running peripheral/SAADC example on the board, I shorted Channel 0 and GND on the board and I am receiving negative values...
Hello
I am using Android and BLE communication with nRF52832 (BLENano2) now.
I am using SDK 15.0.0 with keil uversion.
Central is Android and peripheral is nRF52832...
