Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello,
We are using an nRF52832 (silicon REV C) microcontroller and we see periodic current spikes in between BLE advertisements... our power consumption is higher than...
Hey, I use nrf52 dk with nrf5 usb dongle. I am using this ble_app_uart__saadc_timer_driven__scan_mode example, I think it is working just fine, but the values are in hex-format...
i am not able display uuid, major,minor values and company identifier(so that we can change the beacon identification to ibeacon) using Ble_app_proximity example. please say...
Does the current background DFU support (if not is there a plan to support) Bootloader and SoftDevice updates? It will be extremely useful to update the BL and SD through...
Hi,
i'm using nRF52832 there is easy way/tutorial/explanation how to make it to connect as a client to the mesh app mobile using ble_app_uart_coexist code?
Thx.
Sir,
Writing Android Software to receive bytes from one of your ble chips for the UART design. Editting nrF ToolBox app.
UARTService.java
onDeviceConnected(BlueTooth...
Development Software: SDK v15.3, IDE IAR v7.8, SoftDevice 6.1.1
Computer Platform: Windows
HW revisions: EYSHJNZWZ (nRF52832)
Hi,
My application requires SPI and...
Hello Team,
i am evaluating Custom software Codec inside nrf52840. need development help whether it supports custom codec or not? which bluetooth stack used for development...
I'm working on a NRF52832 project with SDK V15.2, using S132 Softdevice. before connecting, nrf_fstorage_write/nrf_fstorage_erase/sd_flash_write/sd_flash_page_erase all are...
Hi.
I am using SDK15.0.0.
I tested the RF communication through the ESB example.
And I have tested the BLE communication using the ble_app_hids_keyboard example. ...
Hello all
currently I am flashing the device using command line:
#erase chip nrfjprog --family NRF52 --recover #program softdevice nrfjprog --family NRF52 --program...
Hello,
I'm trying to read an ADC value from a sensor(for POC I'll be using a pot wired to 3.3V VDD and GND) but all the examples I found only demonstrated reading the internal...
Hi,
What is your recommended stand-off for your aQFN package to PCB?
Below image is from x-section after mounting nRF52840 to PCB, these are aQFN pads, could you advise...
