But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Setup: nRF5_SDK_15.2.0_9412b96 / s132_nrf52_6.1.0_softdevice / nrf52832
I tried to make a multilink nus central (PCA10040) with 2 peripherals (PCA10028) connected to it...
Hi, I would like to send data from nRF52840 Dongle to Raspberry Pi 3 through USB-UART. I programmed the ble_app_uart_c example found in SDK 15.2 and I connected that to my...
NRF51822 RM 3.0 section 14.1 states each GPIO pin has DETECT, but where is the register to read per-pin detect? From the manual: "Each pin has a separate DETECT signal, and...
Hi,
Now, i want to use SAADC with softdevice of SDK15.0 to make a beacon program.
I migrate SAADC example in nRF5_SDK_15.0.0_a53641a\examples\peripheral to beacon with...
Hi,
I am using nrf_sniffer_2.0.0-beta-2_10Sep2018_3ef662e for capturing ble mesh packets but i am finding LE LL packets of my node with mesh beacons in my wireshark. Even...
Hello, I am new to nordic sdk and tools. I am planning to develop a nRF52840 DK based sensor device that reads I2C temperature sensor data ad broadcast it periodically. Also...
Hi,
I'm testing the BLE_UART example : <InstallFolder>\examples\peripheral\ble_app_uart . For this, I use the nRF52840 with SDK 15.2 and s140 softdevice.
I would like...
So I am using nrf52832 and making a whole new app in ios. My objective of the app is to get the sensor data (specially motion sensor data and accelerometer data) which is...
Hi,
I am trying to add app_uart into the heart rate sensor example. I called uart_config(); in the function function, but when I open the serial monitor, The errors shown...
Trying to build the unmodified light_switch_client_nrf52832_xxAA_s132_6_0_0.emProject from a fresh download of the Mesh SDK.
SDK_ROOT set & successfully tested as instructed...
Hi Team,
This is more like a generic question.
I have 100 beacons and I want to test them all simultaneously kind of a bulk testing.
What are the possible candidates...
Hello,
I would like to use the hardware crypto engine that is a part of nRF52832 chipset. I understand that the access to it is restricted as SoftDevice uses it. I wonder...
I am running into these 3 errors while compiling my program. I tried fixing sdk_config.h.
.\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol app_uart_init (referred...
EDIT: I have added the battery data in percentage to scan response manufacturer specific data. Is that the only possible way?
Hello,
I am working on a beacon application...
Recently, I was trying to use the button to select the specific actions.
Actually, the program is built successfully and it can show the "UART Start!" via serial port, but...
